Installation - EdilKamin AQUAMAXI 28 Instalación Uso Y Mantenimiento

Termochimenea de leña
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 62
IMPORTANT ADVICE
In addition to the contents of this document, please take into
consideration the regulations of the various countries, for
example, in Italy:
- No. 10683 - rewood heat generators:
installation requirements
- No. 10412:2 - hot water heating systems.
Speci c safety requirements for systems provi
ded with residential solid fuel burning applian
ces and combined boiler, not exceeding a total
nominal heat input of 35 kW.
Particularly:
- Before carrying out any assembly it is important to verify
compatibility of the appliance, as stipulated in UNI 10683
standard, paragraphs 4.1 / 4.1.1 / 4.1.2.
- When assembly is completed, the installer must implement
"start-up operations" and issue documentation as required
by UNI 10683 standard in paragraphs 4.6 and 5, respectively.
- The connections, commissioning and veri cation of pro-
per operation of the thermo replace must be carried out
by quali ed personnel, who can implement the electrical and
plumbing connections as required by UNI standards 10683,
paragraph 4.5 and 10412:2, apart from complying with these
assembly instructions.
- Veri cation must be carried out with the replace on and
after having been on for a couple of hours, before covering the
thermo replace, so that you can intervene if need be.
After which, the nishing operations such as:
- setting-up the replace mantel
- mounting the replace covering
- pilasters, painting, etc.
are carried out, once the tests are completed successfully.
Consequently, EDILKAMIN does not accept responsibility for
expenses deriving from demolition as well as construction even
if either occurs as a result, after having replaced any damaged
parts of the thermo replace.
The replace unit must only be installed on oors with adequa-
te load-bearing capacity.
Otherwise, appropriate countermeasures should be taken (such
as a load- plate).
- The appliance should not be used as an incinerator and
should not be used with fuels other than wood.
VERIFY COMPATIBILITY WITH OTHER DEVICES
The thermo replace MUST NOT be installed in the same
space as type B gas heating equipment (e.g. gas boilers, stoves,
and equipment served by an extraction hood - ref. UNI 10683
and 7129).
In general, the thermo replace could create low pressure in
the room, affecting the operation of such appliances or being
affected by them.

INSTALLATION

SAFETY DISTANCES (Fig. 1)
The distances indicated are the minimum required safety
distances from structures made of combustible materials or any
other combustible components.
MINIMUM SAFETY DISTANCES FROM FLAMMA-
BLE MATERIALS
Fig. 1
EXTERNAL AIR INLET
An external connection with a 10 cm diameter crosssection
throughout (refer to the technical table) is absolutely
necessary for the thermo replace to function properly and
is therefore imperative for this to be implemented.
This connection must link the air adjustment mechanism (E),
delivered separately.
The mechanism, delivered separately, may be tted on the left,
right or rear of the replace unit.
Connection can be made with a exible aluminium pipe.
Ensure that the points where there may be dispersion of air are
sealed well.
The air adjustment mechanism (E) can be removed and
mounted on the right side of the thermo replace.
It is recommended to place a protection grille on the outer
part of the air inlet channel, however, ensure that this does not
reduce the cross-section.
For distances longer than 3 m or with bends, increase the given
cross-section by a minimum of 10% to a maximum of 20%.
The intake of external air must enter at oor level (it cannot
enter from above).
- 30
-
E
E

Publicidad

Tabla de contenido
loading

Tabla de contenido