Beretta Exclusive Green E C.S.I. Serie Manual Del Instalador página 26

EXCLUSIVE GREEN E C.S.I. - R.S.I.
PROGRAMMABLE PARAMETERS EXCLUSIVE GREEN E C.S.I.
N.
PARAMETERS DESCRIPTION
PAR.
1 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
2 MINOR PARAMETER
3 INSULATION LEVEL OF BUILDING
10 DHW MODE
11 DHW CIRCUIT MAXIMUM SET-POINT
12 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
13 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
14 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
20 HEATING MODE
21 HEATING CIRCUIT MAXIMUM SET-POINT
22 MINIMUM HEATING SET POINT
23 MAXIMUM HEATING VENTILATOR SPEED (*)
24 MINIMUM HEATING VENTILATOR SPEED (*)
25 DIFFERENTIAL HEATING POSITIVE
26 DIFFERENTIAL HEATING NEGATIVE
28 MAX HEATING POWER REDUCTION TIMER
29 FORCED HEATING SHUT DOWN TIMER
30 HEATING TIMER RESET FUNCTION
31 MAXIMUM HEATING SET POINT 2CH (II circuit)
32 MINIMUM HEATING SET POINT 2CH (II circuit)
35 DIFFERENTIAL HEATING POSITIVE 2CH (II circuit)
36 DIFFERENTIAL HEATING NEGATIVE 2CH (II circuit)
40 DHW THERMOSTAT OPERATING MODE
41 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
42 S.A.R.A. FUNCTION
43 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
44 THERMOREGULATION FUNCTION
45 INCLINATION THERMOREGULATION CURVE (OTC)
46 THERMOREGULATION FUNCTION 2CH
47 INCLINATION THERMOREGULATION CURVE (OTC) 2CH
48 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
50 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
51 HEAT REQUEST TYPE CH1 (I circuit)
52 HEAT REQUEST TYPE CH2 (II circuit)
61 DHW ANTIFREEZE FUNCTION TEMPERATURE (ON)
62 HEATING ANTIFREEZE FUNC. DELIVERY TEMP. (ON)
63 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
65 EXTERNAL SENSOR REACTIVITY
85 SEMI-AUTOMATIC FILLING
86 AUTOMATIC FILLING PRESSURE (ON)
87 THIS PARAMETER IS NOT USED ON THIS MODEL. DO NOT MODIFY
90 ADJUSTABLE SPEED PUMP
92 ENABLE POST-CIRCULATION FROM DHW TO HEATING
93 DURATION OF POST-CIRCULATION FROM DHW TO HEATING
94 PUMP IN CONTINUAL MODE CH1 (CIRCUIT 1)
95 PUMP IN CONTINUAL MODE CH2 (CIRCUIT 2)
* The value is expressed on the display in revs/min/100 (example 3.600 = 36).
Some default values could be different from the one in the table, dependent on the status of data sheet updating
(1) Setted in factory
(2) Settede by technical assistance
26
UNIT OF
MIN
MEASURE
10-16-20-26-30-34-50-70
min 5
0 - OFF
1 - Instantaneous
2 - Mini-tank
3 - External water- tank with
thermostat
4 - External water- tank with sensor
5 - DS integrated water tank
6 - 3S integrated water tank
°C 40
0 - OFF
1 - ON
2 - Zone valves + remote control panel
3 - CONNECT AP
4 - Not used
5 - Not used
6 - CONNECT AT/BT
7 REMOTE CO NTROL+CONNECT
AT/BT
8 REMOTE PANEL + ZONE VALVES
°C 40
°C 20
revs/min
25 kW 45
30 kW 51
35 kW 53
G20 G31
revs/min
25 kW
12 15
30 kW
12 15
35 kW
12 15
°C 2
°C 2
min 0
min 0
0 (NO)
°C 40
°C 20
°C 2
°C 2
0 - OFF
1 - AUTO
2 - ON
0 - OFF
1 - AUTO
0 - OFF
1 - AUTO
2,5
0 - OFF
1 - AUTO
2,5
0
0
°C 0
°C 0
0 (very fast) 255 (very slow)
0 - Disabled
1 - Enabled
bar 0.4
0
0
1
0
0
MAX DEFAULT PARAMETERS
(1)
1
20
20 5
1
60 60
60
80
5
1
80 80
39 20
G20 G31
MAX
45
49
54
MIN
10 6
10 6
20 15
20 5
1 (YES) 0
80 45
39 25
10 3
10 3
1
1
1
1
1
40 20
1
40 10
1
1
1 0
1 0
10 4
10 6
6
20
1
1.0 0.6
1
100 60
1 0
255 5
1 0
1 0
(2)