Assembly Components; Assembly Of The Guide Bar And Toothed Chain - Stiga CS 80 Li Manual De Instrucciones

Ocultar thumbs Ver también para CS 80 Li:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 159
C. Rear handgrip: support handgrip located
on the rear of the chain saw. This should be
grasped using the right hand. This handgrip
is fitted with the main switch controls.
D. Front hand guard: protection device
seated between the front handgrip
and the toothed chain, to protect the
hand against injuries should it slip off
the handgrip. This guard is used as a
device to trigger the chain brake.
E. Rear hand guard: protection device
seated in the lower right section of
the rear handgrip, to protect the hand
from the saw chain should it break
or disconnect from the guide bar.
F.
Guide bar: supports and
guides the toothed chain.
G. Toothed chain: cutting element,
consisting of drive links fitted with
small blades called "teeth" and side
connections held in place by rivets.
H. Chain restraint pin: safety device that
prevents uncontrolled movements of the
toothed chain should it break or slacken.
I.
Spiked bumper: device installed
opposite the guide bar assembly
point acting as a pivot when it comes
into contact with a tree or trunk.
J. Bar cover guard: chain saw cover on
the guide bar to be fitted during handling,
transportation or storage of the machine.
K. Battery: device that supplies electric
current to the tool; its specifications
and regulations for use are
described in a specific manual.
L. Battery charger (attachment on
request, par. 16.2): device used
to recharge the battery.
M. Torque wrench: tool used to rotate screws,
nuts and bolts, to tighten or loosen them.
4. ASSEMBLY
The safety regulations to follow
are described in chap. 2. Strictly
comply with these instructions to
avoid serious risks or hazards.
For storage and transport purposes, some
components of the machine may not be installed
in the factory and have to be assembled after
unpacking. Follow the instructions below.
Unpacking and completing the assembly
should be done on a flat and stable surface,
with enough space for machine handling
and its packaging, always making use of
suitable equipment. Do not use the machine
until all the indications provided in the
"ASSEMBLY" section have been carried out.

4.1 ASSEMBLY COMPONENTS

The packaging includes assembly components.
4.1.1
Unpacking
1. Cautiously open the packaging, paying
attention not to lose components.
2. Consult the documentation in the
box, including these instructions.
3. Remove all the unassembled
parts from the box.
4. Remove the machine from the box.
5. Dispose of the box and packaging in
compliance with local regulations.
4.2 ASSEMBLY OF THE GUIDE
BAR AND TOOTHED CHAIN
Always wear heavy-duty gloves when
handling the bar and chain. Mount the
bar and chain very carefully so as not to
impair the safety and efficiency of the
machine. If in doubt, contact your dealer.
Perform all operations after
removing the battery.
1. Using the supplied wrench, unscrew
the nuts (Fig. 3.A) and remove the
chain guard (Fig. 3.B), to access
the drive pinion and bar seat.
2. Mount the bar (Fig. 4.A) by inserting
the stud bolts (Fig. 4.B) in the groove
(Fig. 4.C) and push it towards the
back of the machine body.
3. Mount the chain around the drive pinion (Fig.
5.A) and along the bar guide, being careful
to follow the sliding direction (Fig. 5.B).
If the tip of the bar is equipped with
a nose sprocket, make sure the
drive links are correctly inserted in
the sprocket rims (Fig. 6.A).
4. Check that chain tension adjuster pin
(Fig. 5.C) is fitted properly in the hole on
the bar; if it isn't, turn the chain tension
adjuster screw (Fig. 5.D) using a screwdriver
until the pin is completely inserted.
5. Replace the guard without
fully tightening the nuts.
6. Turn the chain tension adjuster screw (Fig.
5.D) to achieve the desired tension (Fig. 7).
7. Raise the bar and tighten the guard nuts
securely using the wrench (Fig. 8.A).
EN - 6
Direction in which
the chain runs

Publicidad

Tabla de contenido
loading

Tabla de contenido