Emptying The Grass Catcher; Routine Maintenance; General Information; After Operation - GGP ITALY MP2 504 Serie Manual De Instrucciones

• for particularly high grass, initially mow at the
maximum height allowed by the machine
then mow again after two or three days.
6.4.3

Emptying the grass catcher

When the grass catcher (fig. 1.H) is too full,
grass collection is no longer efficient and the
sound of the lawnmower changes.
For a grass-catcher with contents indicator device:
1. up (a) = empty
2. down (b) = full
While working with the cutting means
running, the indicator remains raised for
as long as the grass catcher is able to hold
cut grass; when it lowers, it means that the
grass catcher is full and must be emptied.
To remove and empty the grass catcher:
– Release the engine / cutting means brake lever
and wait for the cutting means to stop (par. 6.5);
• With "II" type grass-catcher only
– Lift the rear discharge guard (fig. 10.D).
– Grasp the handle and remove the grass-
catcher keeping it in an erect position.
6.5 STOP
To stop the machine:
1. Release the engine / cutting means
brake lever (fig. 19.A);
2. Wait until the cutting means stops;
The engine may be very warm immediately
after it is shut off. Do not touch the exhaust or
adjacent parts. This can cause burn injuries.
Always stop the machine:
– when moving between work areas;
– when driving on grass free surfaces;
– every time it is necessary to overcome an obstacle;
– before adjusting the cutting height.
– whenever you remove or reattach the grass catcher;
– whenever you remove or reattach the
rear discharge chute (if provided);
– whenever you remove or reattach the
side discharge chute (if provided);
6.6

AFTER OPERATION

1. Stop the machine (par. 6.5).
2. Allow the engine to cool before
storing in an enclosed space.
3. Clean (par. 7.4).
Check there are no loose or damaged components.
4.
If necessary, replace the damaged components
and tighten any screws and loose bolts.
IMPORTANT Remove the key (if provided) or the
battery whenever the machine is unused or left unattended
on models with electric push-button ignition controls.
7.

ROUTINE MAINTENANCE

7.1

GENERAL INFORMATION

The safety regulations to follow are
described in chap. 2. Strictly comply with these
instructions to avoid serious risks or hazards.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• stop the engine;
• make sure that all moving parts have
come to a complete stop;
• wait until the engine is sufficiently cold;
• remove the spark plug cap;
• read the relevant instructions;
• Use suitable clothing, protective gloves and goggles.
• The frequency and types of maintenance are summarised
in the "Maintenance Table". The table will help you
maintain your machine's safety and performance.
It lists the main maintenance tasks and how often
they need to be performed. Carry out the relevant
task as soon as it is scheduled to be performed.
• The use of non-genuine and/or incorrectly
assembled spare parts and attachments could
adversely affect machine operation and safety. The
manufacturer shall decline all liability in the event
of injuries or damages caused by such parts.
• Genuine spare parts are supplied by authorized
assistance workshops and dealers.
IMPORTANT All the maintenance and adjustment
operations not described herein must be carried out
by your dealer or Authorised Service Centre.
7.2 REFUELLING
To refuel:
1. Unscrew the tank closure cap and remove it ..
2. Insert a funnel.
3. Refuel and remove the funnel.
4. Close the fuel cap securely after refuelling
and clean away any spills.
NOTE Do not fill the fuel tank right to the top.
IMPORTANT Do not drip petrol onto the plastic parts of
the engine or the machine to prevent damaging them and
remove all traces of spilled petrol immediately. The warranty
does not cover damage to plastic parts caused by petrol.
NOTE Fuel is perishable and should not remain
in the tank for more than 30 days. Before storing for
a long period, fill the tank with a sufficient amount
of fuel to reach final destination (chap. 9).
EN - 8