above steps and install it again.
Installation of Group I for the children
whose weight between 9-18kg with ISOFIX
and Top tether.
17.
Pull out the Top tether and press the
Tether strap release button to extend the
strap until it is long enough to hook the
User-ready tether anchorage behind.
18.
Hook the Tether strap hook onto the
User-ready anchorages. Check there
maybe are 3 anchorages for the hook,
please find one in your favor.
19.
Pull the Tether strap on another end back
to tighten the Top tether.
20. CAUTION
If the Top tether is tightened
favorably and correctly, a green mark will
turn up on the other end of the Strap re-
lease button, please do check it.
Installation of Group II and it is for the
children whose weight between 15-25kg.
21.
Before the installation, please take away
the Harness system of baby car seat.
Note:
The Baby insert, Harness strap,
Harness buckle, Buckle pads, Shoulder
pads & Shoulder belts axle should be
stored away safely for future use (see
Removing the 5-point harness system
and cover ).
IMPORTANT
Do not to use any load bear-
ing contact points other than those de-
scribed in the instructions and marked
in the child restraint.
The belt must be
routed as shown in the manual.
22.
Pull the Belt guide out, and put the
Shoulder belt through the guide, lock the
Belt guide.
23.
Place your child into the baby car seat
and let the car belt pass the Belt guide.
Fasten the car belt with an audible sound
"click".
24.
Make sure the Lap belt is stretched low
and snug across the child's hips, within
the Belt guides, and fastened into the
buckle. The Shoulder belt must cross
midway between child's shoulder and
neck.
Installation of Group III and it is for the
children whose weight between 22-36kg.
25.
Adjuster the height of the headrest to
suit your child.
26.
Refer to the Group II installation instruc-
tions.
Please make sure that any lap strap is
worn low down, so that the pelvis is
firmly engaged.
Installation of Group II/III with car belt
and ISOFIX connector.
OPTIONS!
This car seat also allow to install
with the ISOFIX, please operate as following:
27.
Extend the ISOFIX connectors and fix it
into the ISOFIX anchorages until you hear
an audible sound "click".
Fasten the car belt. Details please refer to
the abovementioned instructions for the
car belt installation for group 2/3.
CARE INsTuRCTIONs
Removing the 5-point harness system
and cover
28.
Adjust the shell to the max inclined posi-
tion, pull the lower shaft out and pull the
seat shell towards.
29.
Push down the adjustment device and
pull the harness strap out the strap yoke
from other side to unlock it.
30.
Pull the shoulder strap axle out, untie
the shoulder strap and pull the harness
strap out from the harness slot.
31.
Loosen the bottom part of the cover and
pull the belt clip through the belt clip
slot. Then pull the buckle clip through
the buckle clip slot.
30
32.
Remove 5-point harness system then
remove the headrest cover and the shell
cover.
Refitting the 5-point harness system and
cover
33.
After washing, place the cover on the
shell.
34.
Loosen the bottom part of the cover and
pull the belt clip through the belt clip
slot. Then pull the buckle clip through
the buckle clip slot.
35.
Put the end of the shoulder strap through
the harness slot, fix into shoulder strap
axle, and lock the shoulder strap axle to
the seat shell .
36.
Also put the end of the harness strap
through the harness strap slot and shell,
fix into the strap yoke, make sure the
seat straps can not be rotated.
37.
Close the buckle, then fasten the cover
all around. Check that it works!
CLEANING
Please be sure to use only original seat cov-
ers, as the seat cover is important to the
proper functioning of the system. Replace-
ment seat covers are available from your
retailer and or at branches.
The child seat
must not be used without the seat cover.
The cover can be removed and washed
with a mild detergent using the washing
machine's cycle for delicate items (30°C).
Please observe the instructions on the
washing label of the cover. The colours of the
cover may fade if washed at more than 30°C.
Do not spin, and never tumble dry in an elec-
tric clothes dryer (the fabric may separate
from the padding). The
plastic parts
cleaned using soapy water.
Do not
use harsh
cleaning agents (such as solvents). The har-
ness can be removed and washed in luke-
warm soapy water. Caution! Never remove
the buckle tongues from the straps.
MATERIALs
Cover:
100% polyester
sIZEs
L: 69 cm;
H: 63 cm;
D: 45 cm.
CHECKLIST
For safety's sake read through this check-
list before you set off. Check that the har-
ness belt system fits properly and tightly
around your child and that the shoulder
belts are at the correct height. Check regu-
larly that the belt in the baby car seat is not
damaged. If it is damaged do not use your
product in any circumstances and contact
your supplier or importer (see address list
in the service card). Check that you have
secured your baby car seat with the seat
belt. If you have any questions, please con-
tact your supplier.
• Make sure that you have the following de-
tails to hand:
• Serial number underneath on the service
card.
• Mark and type of vehicle and seat on which
the baby car seat used.
• Age and weight of your child.
WARNINGs
• FAILURE TO OBSERVE THE AS-
SEMBLY INSTRUCTIONS PROVID-
ED BY THE MANUFACTURER MAY
can be
BE DANGEROUS FOR THE SAFETY
OF THE CHILD.
•
This is a child restraint system ap-
proved Regulation No.44,04 standards,
for three different types of installation:
31