Operation; Maintenance - Titan LazyLiner Pro Instrucciones De Uso

Operation

i
Prior to putting the equipment into operation,
please read the instructions in the operating manual
for Subaru motors carefully through.
1. Check engine oil level. Refer to the supplied engine manual
for recommended oil level and service. The engine normally
comes pretested and filled with oil from the factory.
2. Check transmission oil level in unit by removing the fill cap
on top of the hydraulic tank. Oil level should be 3/4 to 1 inch
from the top of the tank.
If oil is low or if it needs to be changed, always
use Mobil 1™,15W50 full synthetic oil. Never use
"hydraulic oil" in the system.
Attention
3. Remove gas cap and fill tank with regular unleaded gas, make
sure fuel shut off lever is in on position. Replace the gas cap.
4. Sit on the LazyLiner or engage parking brake.
5. Start the engine:
a. Engage parking brake (refer to Figure 1, item 2). Push arm
forward to engage the brake.
b. Move fuel valve to open and choke valve to closed (same
on both electric start or pull start units)
c. Set throttle to high and engine switch to ON (if pull start
unit)
d. Pull engine cord or engage key switch
e. After engine starts, move choke to run position and set
throttle to desired position.
i
The LazyLiner unit can not be started unless the
parking brake is engaged or the operator is in the
seated position, If the brake is not engaged or you
are not seated the Safety switch system will not
allow the engine to start.
6. Grip handle bars and squeeze caster wheel release.
7. Operate pedals in either the forward motion (toe down) or in
reverse (heel down) which ever is needed. Turning the units
is accomplished by using the striper and releasing the caster
wheel.
8. The LazyLiner will achieve desired speed (0-16 KM/h forward,
0-11 KM/h backwards) by pressing harder or lighter on the
pedal assembly.
The unit will come to a complete stop (quickly) once you
allow the pedals to return to center or neutral. The hydraulic
pressure creates the stopping or braking feature to bring your
unit to a stop.
i
If the LazyLiner does not move, the hydraulic release
valve bypass (see Figure 4, item 34) will need to be
tightened. Turn 1/2 to 1 turn clockwise until tight to
engage the drive.
ALWAYS set parking brake when not operating or on
LazyLiner.
GB

Maintenance

Read below in order to know what type of maintenance should be
performed on your LazyLiner at certain intervals of usage.
i
For detailed information about maintenance and
care of the motor, please read the instructions in the
operation manual for Subaru motors.
Daily:
• Check engine oil level and fill as necessary.
• Check oil transmission reservoir level and fill as necessary. Oil
and filter should be changed evey 650-700 hours of service.
• Check and fill the gas tank with regular unleaded gas.
• Check tires and inflate to 1,7 bar (25 PSI) if needed
• Wipe down equipment – Never use a water hose to wash.
• Check and clean air cleaner. Replace when necessary
After first 20 hours:
• Drain and refill engine oil with SAE 10W-30 oil. See
manufacturers specs for API rating.
Weekly:
• Add a small amount of grease to ball coupler inside ball area.
• Check all hardware for integrity. Tighten any loose bolts or
nuts.
Every 50 hours:
• Replace spark plug
• Inspect system for oil leakage from drive assembly.
Every 100 hours:
• Grease Axle Bearings – Moly type grease, two pumps of grease
gun. Wipe excess grease off bearings.
• Drain and refill engine oil with SAE 10W-30 oil. See
manufacturers specs for API rating
• Check and refill if necessary the transmission reservoir.
• Check chain tension and reset idler sprocket to tension if
required. Remove transmission cover and check drive belt.
Re-tension if required.
• Use air supply to remove accumulated dust inside cover.
• Rotate tires to get a more even wear and longer life span. As
the tires wear, the brake assembly will need to be adjusted
to ensure proper contact with the tires. Loosen the two 3/8"
bolts that secure the brake assembly to the frame. Tap the
brake assembly mount towards the rear of the unit 1/8 to 1/4
inch. Retighten the bolts.
8 LazyLiner Pro • Elite