Makita DTDA040 Manual De Instrucciones página 9

Changing the parameter setting on the tool ( Field Setting mode)
NOTICE:
This function is available by default. If you have disabled the Field Setting mode on the computer,
enable this function beforehand. Refer to the instruction manual of Makita Industry Tool Settings for how to
configure.
NOTICE:
If the Field Setting mode is disabled, making settings on the tool is not available. When you press the
setting button, the values set on the tool are displayed in order.
The current setting number is displayed on the indicator.
Every time you press the setting button, the indicator shows torque level, rundown level, workable time range, and Ad .
Fig.7: 1. S etting button 2. I n d i c ator
You can change the following parameter settings on your tool:
• A uto-stop setting / F ree mo d e
Setting item
T orq ue lev el
R und ow n lev el
W orkable time range
NOTICE:
If OP (Loosening Auto Stop mode) is displayed on the indicator, torque level setting and rundown
le v el setting is not a v ailable. I n t h is c ase, c h ange t h e mo d e to T ig h tening A uto S top mo d e, an d t h en set t h e tor q ue
level and rundown level on the computer using Makita Industry Tool Settings .
Changing the torque level
W hen changing the torque level from 23 to 34
Fig.8
1 . P ress t h e setting button se v eral times until t h e
in d i c ator s h o w s 2- d igit number w h i c h stan d s f or
t h e c urrent setting o f t h e tor q ue le v el.
2. P ress an d h ol d t h e setting button until t h e number
in t h e tens pla c e starts blinking.
. Set the number in the tens place by pressing the
setting button briefly. Every time you press the
setting button, t h e in d i c ator s h o w s t h e number
from to and F in a cycle.
4 . P ress an d h ol d t h e setting button until t h e number
in t h e ones pla c e starts blinking.
5 . Set the number in the ones place by pressing the setting
button briefly. Every time you press the setting button, the
indicator shows the number from
6 . P ress and h old th e setting button f or a f ew sec ond s.
NOTE: If you are not sure which torque level is suit-
able for your work, set FF so that the tool operates
in t h e F ree mo d e.
NOTE: If you input
" 00 " .
Changing the rundow n level
W hen changing the rundo w n level from L1 to L2
Fig. 9
1 . P ress th e setting button sev eral times until th e ind ic ator
shows characters beginning with L followed by a num-
ber. T h is stand s f or th e c urrent setting of th e rund ow n lev el.
2. P ress an d h ol d t h e setting button until t h e in d i c a-
tor starts blinking.
Display on the indicator
01 - 4 0
F F
O P
L 1 - L 7
O P
L o: 0.1 - 9 .9
H I : 0.1 - 9 .9
-.-
to and F in a cycle.
, FF is displayed instead of
T h e torq ue lev el at w h ic h th e T igh tening
A uto S top mod e w orks
The sensitivity of the fastener seating
T h e sh ortest/ longest d uration of th e rota-
tion when you continue to pull the switch
trigger.
. Set the rundown level. Every time you press the
setting button, t h e in d i c ator s h o w s f rom " L 1 " to
L in a cycle. The lowest rundown level is L
an d " L 7 " is t h e h ig h est.
4 . P ress and h old th e setting button f or a f ew sec ond s.
Changing the shortest w orkable time
range
W hen changing the shortest w orkable time range
from 2.5 to 3.6
Fig.10
1 . P ress t h e setting button se v eral times until t h e
indicator shows Lo and number alternatively.
T h is stan d s f or t h e c urrent setting o f t h e s h ortest
w orkable time range.
2. P ress an d h ol d t h e setting button until t h e number
in t h e ones pla c e starts blinking.
. Set the number in the ones place by pressing the
setting button briefly. Every time you press the
setting button, t h e in d i c ator s h o w s t h e number
from to
4 . P ress an d h ol d t h e setting button until t h e number
in t h e d e c imal pla c e starts blinking.
. Set the number in the decimal place by pressing
the setting button briefly. Every time you press the
setting button, t h e in d i c ator s h o w s t h e number
from to
6 . P ress and h old th e setting button f or a f ew sec ond s.
NOTE: When you set the value smaller than
t h e s h ortest w orkable time range, t h e in d i c ator s h o w s
" -.- " an d t h e s h ortest w orkable time range be c omes
d isable d . T o input " -.- " , set t h e v alue to " 0. 9 " , an d t h en
press t h e setting button w h en t h e number in t h e ones
pla c e is blinking.
9 ENGLISH
Description
in a cycle.
in a cycle.
. for