Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
CORAL UC300/UC100 Filtration
System Performance Data Sheet
Chemical
alachlor
atrazine
benzene
carbofuran
carbon tetrachloride
chlorobenzene
chloropicrin
2,4-D
dibromochloropropane(DBCP)
o-dichlorobenzene
p-dichlorobenzene
1,2-dichloroethane
1,1-dichloroethylene
cis-1,2-dichloroethylene
trans-1,2-dichloroethylene
1,2-dichloropropane
cis-1,3-dichloropropylene
dinoseb
endrin
ethylbenzene
ethylene dilbromide (EDB)
haloacetonitriles (HAN)
bromochloroacetonitrile
dibromoacetonitrile
dichloroacetonitrile
trichloroacetoritrile
haloketones (HK):
1,1-dichloro-2-propanone
1,1,1-trichloro-2-propanone
heptachlor (H-34,Heptox)
heptachlor epoxide
hexachlorobutadiene
hexachlorocyclopentadiene
lindane
methoxychlor
pentachlorophenol
simazine
styrene
1,1,2,2-tetrachloroethane
tetrachloroethylene
toluene
2,4,5-TP (silvex)
tribromoacetic acid
1,2,4-trichlorobenzene
1,1,1-trichloroethane
1,1,2-trichloroethane
trichloroethylene
trihalomethanes (includes):
chloroform (surrogate chemical)
bromoform
bromodichloromethane
chlorodibromomethane
xylenes (total)
* Chloroform was used as the surrogate chemical for VOC reduction claims
Brondell, Inc
PO Box 470085
San Francisco, CA 94147
www.brondell.com 1-888-542-3355
Drinking Water
Influent Challenge
Regulatory Level
Concentration
(MCL/MAC)
(mg/L unless specified)
(mg/L unless specified)
0.002
0.050
0.003
0.100
0.005
0.081
0.040
0.190
0.005
0.078
0.100
0.077
–
0.015
0.070
0.110
0.0002
0.052
0.600
0.080
0.075
0.040
0.005
0.088
0.007
0.083
0.070
0.170
0.100
0.086
0.005
0.080
–
0.079
0.007
0.170
0.002
0.053
0.700
0.088
0.00005
0.044
–
0.022
–
0.024
–
0.0096
–
0.015
–
0.0072
–
0.0082
0.0004
0.08
0.0002
0.0107
–
0.044
0.050
0.060
0.0002
0.055
0.040
0.050
0.001
0.096
0.004
0.120
0.100
0.150
–
0.081
0.005
0.081
1.000
0.078
0.050
0.270
–
0.042
0.070
0.160
0.200
0.084
0.005
0.150
0.005
0.180
0.080
0.300
10
0.070
1 These harmonized values were agreed upon by representatives of USEPA and Health Canada for the purpose of
evaluating products to the requirements of this Standard.
2 Influent challenge levels are average influent concentrations determined in surrogate qualification testing.
3 Maximum product water level was not observed but was set at the detection limit of the analysis.
4 Maximum product water level is set at a value determined in surrogate qualification testing.
5 Chemical reduction percent and maximum product water level calculated at chloroform 95% breakthrough
point as determined in surrogate qualification testing.
6 The surrogate test results for heptachlor epoxide demonstrated a 98% reduction. These data were used to
calculate an upper occurrence concentration which would produce a maximum product water level at the MCL.
Chemical Reduction
Percent (%)
> 98
> 97
> 99
> 99
98
> 99
99
98
> 99
> 99
> 98
95
5
> 99
> 99
> 99
> 99
> 99
99
99
> 99
> 99
98
98
98
98
99
96
> 99
98
6
> 98
> 99
> 99
> 99
> 99
> 97
> 99
> 99
> 99
> 99
99
> 98
> 99
95
> 99
> 99
95
> 99
Maximum Product
Water Concentration
(mg/L unless specified)
0.001
3
0.003
3
0.001
3
0.001
3
0.0018
4
0.001
3
0.0002
3
0.0017
4
0.00002
3
0.001
3
0.001
3
0.0048
5
0.001
3
0.0005
3
0.001
3
0.001
3
0.001
3
0.0002
4
0.00059
4
0.001
3
0.00002
3
0.0005
3
0.0006
3
0.0002
3
0.0003
3
0.0001
3
0.0003
3
0.0004
0.0002
6
0.001
3
0.000002
3
0.00001
3
0.0001
3
0.001
3
0.004
3
0.0005
3
0.001
3
0.001
3
0.001
3
0.0016
4
0.001
3
0.0005
3
0.0046
4
0.0005
3
0.0010
3
0.015
0.001
3
23
Publicidad
Tabla de contenido
Solución de problemas
