Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATING
CHAIN
SAW
Continued
Trimming
a tree is the process of cutting limbs lrom
a living tree. Make sure your footing is frm. Keep
feet apart. Divide your weight evenly on both feet.
Follow directions
below to trim a tree.
1. Make
first cut six inches
lrom tree trunk
on
underside
of limb. Use top of guide bar to make
this cut. Cut 1/3 through diameter
of limb (see
Figure
16).
2.
Move two to four inches larther
out on limb.
Make second cut lrom above limb. Continue cut
until you cut limb oft:
3.
Make third cut as close to tree trunk as possible
on underside of limb stub. Use top of guide barto
make this cut. Cut 1/3 through diameter of stub.
4.
Make fourth cut directly above third cut. Cut down
to meet third cut. This will remove limb stub.
CLEANING
AND
MAINTENANCE
NOTICE: Below are instructions for ser-
vicing your chain saw. Any servicing
not
mentioned
below should
be done by an
authorized
service
center.
CLEANING
SAW BODY
A
WARNING: Unplug chain saw from
powersourcebeforeservicing. Severeinjury
or death could occur from electrical shock
or body contact with moving chain.
WARNING: Cutting
edges on chain
are sharp. Use protective gloves when
handling
chain.
WARNING: When cleaning saw body,
• do not submerge saw in any liquids
• do not use products that contain am=
monia, chlorine,
or abrasives
• do not use chlorinated
cleaning sol-
vents, carbon tetrachloride,
kerosene,
or gasoline
Keep saw body clean. Use a soft cloth &tmpened witha
mild soap and water mixture. Wipe saw body to dean.
CARE
OF GUIDE
BAR
Uneven bar wear causes most guide bar problems.
Incorrect sharpening of chain cutter and depth gauge
settings often cause this. When bar wears unevenly,
it widens guide bar groove (see Figure 17). This
causes chain clatter and rivet popping. Saw will not
cut straight. Replace
guide bar if this occurs.
Inspect guide bgu be`tore sharpening chain. A worn or
demaged guide bar is unsa`t_. A worn or damaged guide
bar will damage chain. It will also make cutting harder.
Normal Guide Bar Maintenance
1. Remove guide bar from chain saw.
2.
Remove sawdust from guide bar groove periodi-
cally. Use putty knife or wire (see Figure 18).
3.
Clean oil slots after each day of use.
4.
Remove burrs from sides of guide bar. Use flat
file to make side edges square.
Replace
guide bar when
• bar is bent or crocked
• inside groove of bar is badly worn
Note: When replacing
guide bar, see Ru)lacemem
Pmls atzd Accessories,
page 2 l, `t_)rproper bar.
SHARPENING
SAW CHAIN
£k
WARNING: Unplug chain saw from
powersource beforeservicing. Severeinjury
or death could occur from electrical shock
or body contact with moving chain.
_Ib WARNING:
Cutting
edges on chain
are sharp.
Use protective gloves when
handling
chain.
Keep chain sharp. Your saw will cut ,taster and more
safely. A dull chain will cause undue sprocket,
guide
bar, chain, and motor wear. If you must force chain
into wood and cutting creates only sawdust with few
large chips, chain is dull.
items Needed to Sharpen Chain
Purchase
these items from your local dealer, hard-
ware store, or chain saw supplies outlet.
• 5/32" round file
• Depth gauge tool
• File guide
• Vise
• Medium sized fiat file
Sharpening
Cutters
Use file guide for 30 ° filing.
1. Adjust chain %r proper tension (see Sav,' Chailz
Temiolz Adjustmem,
pages 16 and 17).
2.
Clamp guide bar in vise to hold saw steady. Note:
Do not clamp chain.
3.
Press 5132" round
file (attached
to file guide)
into groove between top plate and depth gauge
on chain. File guide should rest on both top plate
and depth gauge (see Figure
19). Note:
File at
midpoint
of guide bar.
www, desatech.com
90
108539
Publicidad
