Publicidad
Idiomas disponibles
Idiomas disponibles
TOP PANEL FEATURES
7
6
8
5
9
4
3
10
2
20
1.
POWER LED – Illuminates when the mixer is on.
2.
MIC ON/OFF – Turns the microphone input on or off.
3.
MIC GAIN – Adjusts the audio level of the microphone signal.
4.
MIC BASS – Adjusts the low (bass) frequencies of the microphone channel.
5.
MIC TREBLE – Adjusts the high (treble) frequencies of the microphone channel.
Tip: If you experience feedback when using a microphone at loud levels, try turning down the high frequencies.
6.
MIC INPUT – Connect a microphone to this input with an XLR or ¼" cable.
7.
CHANNEL GAIN – Adjusts the corresponding channel's pre-fader and pre-EQ gain level.
8.
CHANNEL TREBLE – Adjusts the high (treble) frequencies of the audio on the corresponding channel.
9.
CHANNEL MID – Adjusts the mid-range frequencies of the audio on the corresponding channel.
10.
CHANNEL BASS – Adjusts the low (bass) frequencies of the audio on the corresponding channel.
11.
INPUT SELECTOR – Selects the input source to be routed to the corresponding channel. Input jacks are located on the
rear panel.
12.
CHANNEL FADER – Adjusts the audio level on the corresponding channel.
13.
PFL –Sends pre-fader, pre-EQ audio of the corresponding channel to the Cue channel for headphone monitoring.
14.
CUE GAIN – Adjusts the audio level of the Cue channel.
15.
CUE BLEND – Slide this to mix the Cue channel and Program mix in the headphones. When all the way to the left, only
channels routed to the Cue channel will be heard. When all the way right, only the Program mix will be heard.
16.
BLEND / SPLIT – When pressed, this button sends all audio in the Cue channel to the left side of the headphones and
the Program mix to the right side of the headphones. When raised, you may control the balance of the Cue channel and
Program mix with the CUE BLEND fader (see #15).
17.
HEADPHONES – Connect your ¼" headphones to this output for cueing and mix monitoring.
18.
CROSSFADER – Blends audio between the channels assigned to the left and right side of the crossfader (see #19).
Note: The crossfader is user-replaceable if it should ever wear out. Simply remove the facepanel, then remove the
screws holding it in position. Replace the fader with a quality authorized replacement from your local Numark retailer
only.
19.
CROSSFADER ASSIGN – Selects which input channel will be heard when the crossfader is moved towards this knob.
All channels not assigned will remain active.
20.
FADER START – Enables or disables "fader start" on the corresponding side of the crossfader. When fader start is
enabled on one side, moving the crossfader toward that side will cause any fader start-compatible device (connected to
the FADER START output on the rear panel) to start playing.
21.
MASTER FADER – This control adjusts the output volume of the Program mix.
22.
STEREO / MONO – Adjusts the Program mix for stereo or mono operation.
23.
BALANCE – Adjusts the balance of right to left audio in all outputs (MASTER, RECORD, and ZONE OUTPUTS).
24.
METER MODE – Determines whether audio from the Program mix or the Cue channel is sent to the STEREO LEVEL
INDICATOR.
25.
STEREO LEVEL INDICATOR – Monitors the audio level of the Master output or Cue Channel, depending on the
position of the METER MODE button.
26.
ZONE – Controls the audio level of the RECORD and ZONE OUTPUTS.
Tip: The RECORD and ZONE OUTPUTS can be used to supply line-level audio to a lighting controller or sound-
activated lighting system.
7
7
11
11
12
12
8
8
9
9
13
13
10
10
18
19
7
7
11
11
12
12
8
8
9
9
13
13
10
10
20
19
6
23
26
11
12
1
24
21
22
13
25
25
16
17
15
14
Publicidad
