General Description Of The Machine; Technical Data - Zhermack ARIO 35 Manual Del Usuario

When using the ARIO 35 laboratory micromotor,
the operator must wear protective gloves and
goggles and keep the area surrounding the
machine clear of persons who could be damaged
by splinters of material or machining waste.
The machine has an electrical circuit. In the event
of even a small fire, extinguish with a dry powder
extinguisher only. The use of water is prohibited.
CHAPTER 3: DESCRIPTION OF THE MACHINE
EN
3.1

GENERAL DESCRIPTION OF THE MACHINE

The machine described in this manual is the ARIO 35
laboratory micromotor designed for milling and/or
polishing dental models.
3.2
DESCRIPTION OF CONTROL UNIT COMPONENTS - Fig. A
1. Green LED
2. Speed regulator
3. ON/OFF switch
4. RH/LH rotation selector
5. Handpiece connector
6. "HAND / FOOT" selector
7. Fuse
8. Pedal connector
9. 220V / 110V selector
10. Power cable and plug
3.3
DESCRIPTION OF HANDPIECE COMPONENTS - Fig. B
11. Brass pin
12. Handpiece handle
13. Terminal
14. Shielded cable
15. Handpiece support
16. Handpiece connector (3 pole)
3.4 DESCRIPTION OF PEDAL COMPONENTS - Fig. C
17. Pedal connector (2 pole)
18. ON/OFF pedal switch
3.5 MACHINE ID DATA
Fig. D: The machine described in this manual is fitted with
a rating plate indicating the ID of the machine and the
manufacturer:
A Manufacturer's name and address
B Machine code and model
C Serial number
D Power supply information
The equipment has been built in compliance with the
EEC Directives stated in the attached "CE Declaration
of Conformity. Use the identification data to request
spare parts, information and After-Sales Assistance
from authorised centres. If the plate should deteriorate
with use and become illegible, even partially, request a
replacement from the Manufacturer stating all data.
22
The reference figures can be found on pages 3, 4, 5 and 6 of this manual.
Do not remove and/or ruin the plate so that the
equipment identification data can be recognised
at all times.
3.5.1 SYMBOLS PRESENT ON THE MACHINE
The following symbols are displayed on the control unit
control panel (see par. 3.2):
Fig. E: Selection button tool rotation direction
Fig. F: Tool rotation speed adjustment
Fig. G: Handpiece connector
CHAPTER 4: TECHNICAL CHARACTERISTICS
4.1 TECHNICAL CHARACTERISTICS AND
OPERATING PRINCIPLE
Zhermack creates qualitatively and technological
advanced equipment which gives the dental technicians
who use it every day the impression that it has been
designed and conceived to precisely satisfy their needs.
Zhermack creates its products using pioneering design
tools to optimise functionality. Zhermack products are
guaranteed by the use of top quality materials and
exhaustive testing to ensure operator safety, making
them competitive at an international level.
Its lightness and versatility make the new ARIO
35 laboratory micromotor an indispensable piece of
equipment in the modern dental laboratory. Functioning
of the ARIO 35 micromotor is based on:
• electronic microprocessor control to optimise
performance and the working life of the motor;
• precision mechanics with top quality materials and
components;
• rapid maintenance thanks to the kit supplied;
• traditional DC motor (with manifold) with high torque
values and maximum revolutions of 35,000 rpm.
4.2

TECHNICAL DATA

Power supply voltage
Total power
Max. rotation speed
Protection rating IP
Noise level
Overvoltage category
Applicable pollution degree
4.2.1 STANDARD EQUIPMENT
Component
Double ended spanner
Brushes with spring
Fuse 5x20 2A
Key
4.2.2 WEIGHT AND DIMENSIONS
Control unit dimensions
Height (mm)
Length (mm)
Depth (mm)
Weight (kg)
230 V~ ± 10% 50/60 Hz
100 Watt
35.000 rpm
IPX0
<70 dB
II
2
Quantity
1
2
1
1
78
112
147
1,25
ARIO 35