Power Supply; Water Supply; Technical Data - DXV AT200 LS SpaLet Manual De Instalación

POWER SUPPLY

Install the cord and outlet according to the
specifications below.
The power distribution work should be done by an
electrical contractor.
• Use an AC120V power supply with a
consumption rating.
If the product is used with other electric appliances,
set the corresponding number of outlets.
• The wiring should be appropriate for the rated
power consumption.
• Set the outlet within the reach of the cord and
high enough from the floor so that water does
not reach it. The length of the power cord
is 39-3/8".
Do not insert the power plug into the outlet until
the installment is complete. There is danger of
malfunction.

WATER SUPPLY

• Only use potable water as the water supply.
Using a different water supply (industrial water,
well water, etc.) may cause the durability of the
electrical and mechanical components to
deteriorate, resulting in an accident or malfunction.
• The water pressure must be more than 14.5 PSI
(when flows) or 109 PSI (hydrostatic pressure).
If the water pressure is lower than the above,
please consult your plumber.
• If the water pressure is higher than 109 PSI,
decompress the pressure by using a
decompression valve.
MINIMUM INSTALLATION CLEARANCE
For the required minimum installation clearance,
refer to the figure below.
* 1 A space of 2 -3/4" or more on each side of the
product is recommended. If it is less than
2 -3/4", it may hinder the operation.
* 2 Place the water shutoff valve to 2" from the wall.
9/16" min.(15 mm)
2*
2" min.
(50 mm)
41-5/16" min.
(1050 mm)
1*
2-3/4"
min.
(70 mm)
19-5/16"
(491mm)
14-3/4"
27-9/16"
(375 mm)
min.
(700 mm)
1*
2-3/4"
min.
(70 mm)
- 4 -
FIRMLY FIX THE WATER SUPPLY PIPE
An impact applied to the hose due to high water
pressure may cause vibrations.
Fix the water supply pipe firmly so that it does not
loosen.There is a danger vibration or flooding.

TECHNICAL DATA

Rated voltage
AC120V 50/60Hz
Rated power consumption
850 W (environment 68°F, water 59°F)
Max rated power consumption
1440 W (environment 68°F, water 59°F)
Length of the power cord
39-3/8"
Length of the water supply hose
26-3/8"
Waterproof grade
IPX4
Water pressure range
0.1MPa{1.0 bar} [when flows 14.5PSI] ~
0.75MPa{7.5 bar} [hydrostatic pressure 109 PSI]
Water connection cross section
R1/2
Operating temperature range
30°F - 104°F
Units
V = volt, Hz = hertz, W = watt, m = meter,
MPa =mega pascal, in = inch,
°C = degrees Celsius, °F = degrees Fahrenheit,
PSI = pounds square inch
Flushing water volume
P-trap: full 1.32 gallons, light .90 gallons
14-3/4"
(375 mm)
9-1/16"
(230 mm)
Finish
Wall
26-9/16"
Finish
(674 mm)
Wall
25-13/16"
(655 mm)
5-15/16"
(150 mm)
3-1/4" (82 mm)
7-1/16" (179 mm)
15-3/4"
(400 mm)
Drainage Pipe
3-9/16"-3-15/16" (90-100 mm)
7-1/2" (190 mm)
12" (305 mm)
7302348-100 (11/17)