Additional Warnings - Evolution R355CPS Instrucciones Originales

www.evolutionpowertools.com
operator, if proper precautions are taken.
b) If the blades are binding, or when
interrupting a cut for any reason, release the
trigger and hold the saw motionless in the
material until the blade comes to a complete
stop. Never attempt to remove the saw from the
work or pull the saw backward while the blade is
in motion or kickback may occur. Investigate and
take corrective actions to eliminate the cause of
blade binding.
c) When restarting a saw in the workpiece, centre
the saw blade in the kerf and check that saw
teeth are not engaged into the material. If saw
blade is binding, it may walk up or kickback from the
workpiece as the saw is restarted.
d) Support large panels to minimise
the risk of blade pinching and kickback. Large
panels tend to sag under their own weight.
Supports must be placed under the panel on
both sides, near the line of cut and near the edge
of the panel.
e) Blade depth and bevel adjusting locking
levers must be tight and secure before
making a cut. If the blade adjustment
shifts while cutting it may cause binding
and kickback.
f) Do not use dull or damaged blades.
Unsharpened or improperly set blades produce
a narrow kerf causing excessive friction, blade
binding and kickback.
g) Use extra caution when making a "plunge
cut" into existing walls or other blind areas.
The protruding blade may cut objects that
can cause kickback.
h) Check lower guard for proper closing
before each use. Do not operate the saw if lower
guard does not move freely and close instantly.
Never clamp or tie the lower guard into the open
position. If saw is accidentally dropped, lower
guard may be bent. Raise the lower guard with
the retracting handle and make sure it moves
freely and does not touch the blade or any other
part, in all angles and depths of cut.
i) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate sluggishly
due to damaged parts, gummy deposits, or a
build-up of debris.
j) Lower guard may be retracted manually
only for special cuts such as "plunge cuts"
and "compound cuts." Raise lower guard by
retracting handle and as soon as blade enters the
material, the lower guard must be released. For
all other sawing, the lower guard should operate
automatically.
k) Always observe that the lower
guard is covering the blade before
placing saw down on a bench or the floor.
An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade
to stop after switch is released.
WARNING: If any parts are missing, do not
(3.4)
operate your machine until the missing parts are
replaced. Failure to follow this rule could result in
serious personal injury.

ADDITIONAL WARNINGS

1. Keep guards in place and in working order.
2. Remove adjusting keys and wrenches.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
3. Keep work area clean. Cluttered areas and
benches invite accidents.
4. Don't use in dangerous environment. Don't
use power tools in damp or wet locations, or
expose them to rain. Keep work area well lit.
5. Keep children away. All visitors should be
kept safe distance from work area.
6. Make workshop child proof with padlocks,
master switches, or by removing starter keys.
7. Don't force the tool. It will do the job better
and safer at the rate for which it was designed.
8. Use the right tool. Don't force the tool or
attachment to do a job for which it was not
designed.
9. Use proper extension cord. Make sure
your extension cord is in good condition. When
using an extension cord, be sure to use one
heavy enough to carry the current your product
will draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and
overheating. The table on the next page shows
the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use
the next heavier gauge. The smaller the gauge
number, the heavier the cord.
10. Wear proper apparel do not wear loose
clothing, gloves, neckties, rings, bracelets, or
other jewellery which may get caught in moving
parts. Nonslip footwear is recommended. Wear
protective hair covering to contain long hair.
11. Always use safety glasses. Also use face or
dust mask if cutting operation is dusty. Everyday
eyeglasses only have impact resistant lenses,
they are not safety glasses.
12. Secure work. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and it frees both hands to operate tool.
13. Don't overreach. Keep proper footing and
balance at all times.
14. Maintain tools with care. Keep tools
sharp and clean for best and safest performance.
Follow instructions for lubricating and changing
accessories.
15. Disconnect tools before servicing; when
changing accessories, such as blades, bits,
cutters, and the like.
16. Reduce the risk of unintentional stating.
Make sure switch is in off position before
plugging in.
17. Use recommended accessories. Consult
the owner's manual for recommended
accessories. The use of improper accessories may
9
EN