Additional Warnings - Evolution S355 CPSL Instrucciones Originales

www.evolutionpowertools.com
complete stop. Never attempt to remove the
saw from the work or pull the saw backward
while the blade is in motion or kickback may
occur. Investigate and take corrective actions
to eliminate the cause of blade binding.
c) When restarting a saw in the workpiece,
centre the saw blade in the kerf and check that
saw teeth are not engaged into the material. If
saw blade is binding, it may walk up or kickback
from the workpiece as the saw is restarted.
d) Support large panels to minimise
the risk of blade pinching and kickback.
Large panels tend to sag under their own
weight. Supports must be placed under
the panel on both sides, near the line
of cut and near the edge of the panel.
e) Blade depth and bevel adjusting locking
levers must be tight and secure before
making a cut. If the blade adjustment
shifts while cutting it may cause binding
and kickback.
f) Do not use dull or damaged blades.
Unsharpened or improperly set blades
produce a narrow kerf causing excessive
friction, blade binding and kickback.
g) Use extra caution when making a "plunge
cut" into existing walls or other blind areas.
The protruding blade may cut objects that
can cause kickback.
h) Check lower guard for proper closing
before each use. Do not operate the saw if
lower guard does not move freely and close
instantly. Never clamp or tie the lower guard
into the open position. If saw is accidentally
dropped, lower guard may be bent. Raise the
lower guard with the retracting handle and
make sure it moves freely and does not touch
the blade or any other part, in all angles and
depths of cut.
i) Check the operation of the lower guard
spring. If the guard and the spring are not
operating properly, they must be serviced
before use. Lower guard may operate
sluggishly due to damaged parts, gummy
deposits, or a build-up of debris.
j) Lower guard may be retracted manually
only for special cuts such as "plunge cuts"
and "compound cuts." Raise lower guard by
retracting handle and as soon as blade enters
the material, the lower guard must be released.
For all other sawing, the lower guard should
operate automatically.
k) Always observe that the lower
guard is covering the blade before
placing saw down on a bench or the floor.
An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in
its path. Be aware of the time it takes for the
blade to stop after switch is released.
WARNING: If any parts are missing, do not
(3.3)
operate your machine until the missing parts
are replaced. Failure to follow this rule could
result in serious personal injury.

ADDITIONAL WARNINGS

1. Keep guards in place and in working order.
2. Remove adjusting keys and wrenches.
Form habit of checking to see that keys and
adjusting wrenches are removed from tool
before turning it on.
3. Keep work area clean. Cluttered areas and
benches invite accidents.
4. Don't use in dangerous environment.
Don't use power tools in damp or wet
locations, or expose them to rain. Keep
work area well lit.
5. Keep children away. All visitors should be
kept safe distance from work area.
6. Make workshop child proof with
padlocks, master switches, or by removing
starter keys.
7. Don't force the tool. It will do the job
better and safer at the rate for which it was
designed.
8. Use the right tool. Don't force the tool or
attachment to do a job for which it was
not designed.
9. Use proper extension cord. Make sure
your extension cord is in good condition.
When using an extension cord, be sure to use
one heavy enough to carry the current your
product will draw. An undersized cord will
cause a drop in line voltage resulting in loss of
power and overheating. The table on the next
page shows the correct size to use depending
on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge. The
smaller the gauge number, the heavier the
cord.
10. Wear proper apparel do not wear
loose clothing, gloves, neckties, rings,
bracelets, or other jewellery which may get
caught in moving parts. Nonslip footwear is
recommended. Wear protective hair covering
to contain long hair.
11. Always use safety glasses. Also use
face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant
lenses, they are not safety glasses.
12. Secure work. Use clamps or a vise to hold
work when practical. It's safer than using your
hand and it frees both hands to operate tool.
13. Don't overreach. Keep proper footing
and balance at all times.
14. Maintain tools with care. Keep tools
sharp and clean for best and safest
performance. Follow instructions for
lubricating and changing accessories.
15. Disconnect tools before servicing; when
changing accessories, such as blades, bits,
cutters, and the like.
16. Reduce the risk of unintentional
stating. Make sure switch is in off position
before plugging in.
17. Use recommended accessories. Consult
the owner's manual for recommended
accessories. The use of improper accessories
may cause risk of injury to persons.
18. Never stand on the tool serious injury
11
EN