Publicidad
Idiomas disponibles
Idiomas disponibles
It is also necessary to replace the 120 volt plug, sup-
plied with the motor, with a UL/CSA Listed plug suitable
for 240 volts and rated current of the saw. Contact a
local qualified electrician for proper procedures to install
the plug. The table saw must comply with all local and
national electrical codes after the 240 volt plug is
installed.
The table saw with a 240 volt plug should only be con-
nected to an outlet having the same configuration as
the plug shown in Figure "1C'. No adapter is available
or should be used with the 240 volt plug.
MAKE CERTAIN that masks or respirators are
MSHA/NIOSH approvedl.
The operation of any Table Saw can result in debris
being thrown into your eyes, which can result in severe
eye damage. ALWAYS wear Safety Goggles (that com-
ply with ANSi standard Z87.1) when operating the Table
Saw. Safety Goggles are available at Sears Retail
Stores. Keep your thumbs and fingers away from the
blade while it is spinning.
Fig. 1 C
current
240 VOLT
carrying
prongs
grounding blade is
longest of the 3 blades
grounded outlet box
©
©
MAKE CERTAIN the receptacle in question is properly
grounded. If you are not sure have a qualified electri-
cian check the receptacle.
This Table Saw is for indoor use only. Do not expose to
rain or use in damp locations.
SPECIFIC
SAFETY INSTRUCTIONS
FOR TABLE SAWS
CALIFORNIA
PROPOSITION
65
SOME DUST CREATED BY POWER SANDING,
SAWING, GRINDING,
DRILLING AND OTHER CON=
STRUCTION ACTIVITIES contains chemicals known to
cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other
masonry products, and
• arsenic and chromium from chemically-treated
lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated
area, and work with approved safety equipment, such
as those dust masks that are specially designed to filter
out microscopic particles.
Basic precautions should always be followed when
using your Table Saw. To reduce the risk of injury,
electrical shock or fire, comply with the safety rules
listed below:
1.
READ and understand the instruction manual
before operating the Table Saw.
2.
DO NOT OPERATE
THiS
MACHINE
until it is
assembled and installed according to the instructions.
3.
OBTAIN ADVICE FROM YOUR SUPERVISOR,
instructor, or another qualified person if you are not
familiar with the operation of this machine.
4.
DO NOT leave the Table Saw plugged into the elec-
trical outlet. Unplug Table Saw from the outlet when
not in use and before servicing, changing blades
and cleaning.
5.
ALWAYS turn the power switch "OFF" before
unplugging the Table Saw.
6.
TO REDUCE THE RiSK OF ELECTRICAL
SHOCK, do not use outdoors.
Do not expose to
rain. Store indoors.
7.
FOLLOW all electrical and safety codes, including
the National Electric Code (NEC) and the
Occupational Safety and Health Regulations
(OSHA). All electrical connections and wiring should
be made by qualified personnel only.
8.
DO NOT handle the plug or Table Saw with wet
hands.
9.
USE only as described in this manual. USE acces-
sories only recommended by Sears.
10. DO NOT pull the Table Saw by the power cord.
NEVER allow the power cord to come in contact
with sharp edges, hot surfaces, oil or grease.
11. DO NOT unplug the Table Saw by pulling on the
power cord. ALWAYS grasp the plug, not the cord.
12. REPLACE a damaged cord immediately. DO NOT
use a damaged cord or plug. If the Table Saw is not
operating properly, or has been damaged, left out-
doors or has been in contact with water, return it to
a Sears Service Center.
13 DO NOT use the Table Saw as a toy. DO NOT use
near or around children.
Publicidad
