[_] OPERATION
1.3
5
Either turn the FUNCTION/SELECT
dial on the main unit
or press the FUNCTION
button
on the remote
control
unit to select the input source you want to play.
FUNCTION
SSELECT
Main unit
Remote control unit
•
The function
switches
as shown
below,
•
The function
only changes in the "--)" direction when
operated
from the remote
control unit.
_
TUNER
_
DVD
_
TV/DBS
CDR/TAPE
_
VCR
_
V.AUX
If "DVD',
"TV/DBS"
or "MAUX"
is selected
as the
input source, press the INPUT MODE button on the
remote
control unit to select the input mode.
Remote
control
unit
AUTO_
PCM _
DTS_ANALOG,
•
"ANALOG"
cannot
be
selected
when
"DVD"
is
selected
as the input source,
Input mode
selection
function
This can be selected
for the "DVD",
"TV/DBS"
and
"MAUX"
input sources.
Different
input
modes
can be
selected
for
the
different
input sources,
The selected
input modes
for the separate
input sources
are stored
in the
memory,
_
AUTO (auto mode)
In this mode, the types of signals being input to the
digital and analog input jacks for the selected
input
source are detected
and the program
in the ADV-
700's surround
decoder
is selected
automatically
upon playback.
®
®
®
2
/ gO(_,_
iii3
Q
i5
3
The
presence
or absence
of
digital
signals
is
detected,
the signals
input to the digital input are
identified
and decoding and playback are performed
automatically
in DTS,
Dolby
Digital
or
PCM
(2
channel
stereo) format.
If no digital signal (TV/DBS
and MAUX) is being input, the analog input jacks are
selected.
Use this mode to play Dolby Digital signals,
PCM (exclusive
PCM signal playback
mode)
Decoding
and playback
are only performed
when
PCM signals are being input,
Note that noise may be generated
when
using this
mode to play signals other than PCM signals.
DTS (exclusive
DTS signal playback
mode)
Decoding
and playback
are only performed
when
DTS signals are being input,
ANALOG
(exclusive
analog
audio
signal playback
mode)
The
signals
input to
the analog
input
jacks
are
decoded
and played,
(This cannot be selected
in the DVD mode.)
NOTE:
•
The input mode
is automatically
set to "AUTO"
when
the input is switched
to DVD.
Either press the SURROUND
MODE button on the
main unit then turn the FUNCTION/SELECT
dial or
press the SURROUND
button on the remote
control
unit to select the play mode.
FUNCTION
/SELECT
Main unit
Main unit
Remote control
unit
•
The function
switches
as shown
below.
•
The function
only changes in the "-_" direction when
operated
from the remote
control unit.
STEREO <4_ AUTO DECODE _H_ 5CH STEREO _
MONO MOVIE
ROCKARENA
_
JAZZCLUB
_
VIDEOGAME
MATRIX
_
VIRTUAL
_
DIRECT _
STEREO ""
Start playback on the selected
component.
•
For operating
instructions,
refer to the component's
manual.
Either turn the MASTER VOLUME
dial on the main unit
or use the VOLUME
buttons
on the remote
control unit
to adjust the volume.
H.. i..ii-ii i iHF
-....:::=i:::i _The
volume
level is displayed
on
I
....... nthe
display.
__MASTER
VOLUME
_._b
Main unit
Remote control unit
Input
mode display
•
In the AUTO mode
•
In the DIGITAL
PCM mode
Lit
f'DIG';
AUTO
',_,N&;"
I
-
....
_
One of these fights, depending
on the input s_gnal
-- DIG
•
In the DIGITAL
-DIG
DTS
DTS mode
/
I
•
In the ANALOG
mode
Input
signal display
•
DOLBY DIGITAL
The volume can be adjusted
within the range of -60
to 0 to 18 dB. However,
when the channel level is set
as described,
if the volume
for any channel
is set at
•
DTS
+1 dB or greater, the volume
cannot be adjusted
up
to
18 dB.
(In this
case
the
maximum
volume
adjustment
range is "18 dB --
(Maximum
value of
•
PCM
channel
level)".)
NOTE:
•
The digital input indicator will light when "DIG"
playing
CD-ROMs
containing
data other than audio signals, but
no sound will be heard.
Input mode when playing DTS sources
•
Noise will be output
if DTS=compatible
CDs or LDs are
played in the "ANALOG"
or "PCM"
mode,
When
playing
DTS-compatible
sources,
be
sure
to
connect the source component
to the digital input jacks
(OPTICAWCOAXIAL)
and set the input mode to "DTS'.
•
Noise may be generated
at the beginning
of playback
and while searching
during DTS playback
in the AUTO
mode. If so, play in the DTS mode.
Checking the currently
playing program
source,
etc.
Either press the STATUS button
on the main unit then
turn the FUNCTION / SELECT dial or press the STATUS
button
on the remote
control
unit to check
the unit's
operating status.
[
:
- ANA -
Main unit
Main unit
Remote control
unit
_ DIG_-
rIIpRO
LOGIC ;T
DBDIGITAL
_L
I
_
_
I
/
Oneof these
-- DIG -
lights.
_
depending on
/
_
th_ input signal
- DIG_-
•
The
"DIG"
lights
when
digital
signals
are
being
input
properly.
If the LED does not light, check whether
the digital
input component
setup
and connections
are correct
and
whether
the component's
power
is turned on.
19