Setting The Operating Mode; Technical Data - Leuze electronic MSI-SR-SM42OS Serie Instrucciones De Uso Originales

Behaviour of the device in the case of an error
The detection of random or systematic system errors in the
system or its control results in deactivation. In doing so, all safety-
oriented output circuits are switched off and the ERR LED of the
module lights or flashes. Error codes are also output via the signal
output X1 and the LEDs of the inputs.

Setting the operating mode

Operating
mode
A-1
− Incremental encoder with HTL output
A-2
− Incremental encoder with HTL output
B-1
− Sensor with PNP output
B-2 − Sensor with PNP output
1)
− Incremental encoder with HTL output
B-3
− Sensor with PNP output
− Incremental encoder with HTL output
C-1
− Sensor with PNP output
− Incremental encoder with HTL output
C-1
− Sensor with PNP output
− Incremental encoder with HTL output
D-1
− Sensor with PNP output
− Incremental encoder with HTL output
D-1
− Sensor with PNP output
In operating mode B-2, the specified safety level can only be adhered to if the sensor lines are individually sheathed and laid so that they are
1)
protected.

Technical Data

Power circuit (A1, A2)
Operating voltage U , DC
B
Rated voltage U
N
Residual ripple U
SS
Rated power DC
Peak current I
P
Ready time t (after applying U
on
Fuse Class gG or circuit breaker
Input circuit (I2, I3, I4, I5, I6, S1, S2)
Input voltage U (HIGH)
e
U (LOW)
e
Input current I (HIGH)
e
I (LOW)
e
Input capacitance, C
IN
Input resistance R
IN
Duty cycle t
E
Break time t
A
Interruption time of U (test pulses)
e
Input circuit (I1, I2, I3, I4)
Input voltage U (HIGH)
e
U (LOW)
e
Input current I (HIGH)
e
I (LOW)
e
Input capacitance, C
IN
Input resistance R
IN
Cutoff frequency
Frequency change
Measurement accuracy of the
frequency measurement
Pulse duration LOW level (for f<100 Hz)
Pulse duration High level (for f<100 Hz)
LOW level (for 100 Hz< f< 2 kHz)
High level (for 100 Hz< f< 2 kHz)
Leuze electronic GmbH + Co. KG
info@leuze.de • www.leuze.com
Input Assignment
Sensor S1
low
low
high
high
)
B
In der Braike 1 D-73277 Owen
Tel. +49 (0) 7021 573-0
Three error categories are distinguished:
• ERR lights: system error, all outputs are deactivated.
• ERR flashes: serious error, all outputs are deactivated.
• ERR off: no errors or minor process errors
Detailed information can be found in the manual.
The deactivation can be revoked if necessary by the user by
elimination of an error (e.g. in the control) and by switching off
the operating voltage and then switching it on again.
S2 I1
Sensor 1
low
Sensor 1
high Sensor 1
Sensor 1
Sensor 1 PLC signal
low
Sensor 1
HIGH signal
Sensor 1 PLC signal
high
Sensor 1
HIGH signal
min
19.2 V DC
−
−
−
−
5 sec. + 1/f
13.0 V
-0.5 V
2.4 mA
-2.5 mA
52 ms
52 ms
−
13.0 V
-0.5 V
2.4 mA
-2.5 mA
1%
(<1Hz)
> 600 µs
> 600 µs
> 200 µs
> 200 µs
I2 I3
Sensor 2 Sensor 1
inverted
Sensor 1 low
inverted
Sensor 2 low
low high
Sensor 1
inverted
static Sensor 1
inverted
low
static low
typical
24 V DC
24 V DC
−
2.5 W
−
ST
4 A (gG)
−
−
3.0 mA
−
10 nF
7200 Ω
−
−
−
−
−
10 nF
7200 Ω
6 %
(<50Hz)
We reserve the right to make changes
01/2018 - 50134634-01 - 8/27
I4
Sensor 2
inverted
low
high
low
low
high
low
high
max
30 V DC
−
3.0 V
3.0 W
25 A
30 V
5.0 V
3.8 mA
2.1 mA
70 ms
70 ms
4.0 ms
30 V
5 V
3.8 mA
2.1 mA
2 kHz
21 kHz/s
12 %
(≤99Hz)