Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

KIT COMPONENTS
• A) Radio trim panel with touchscreen display • B) Radio brackets • C) Pocket • D) Engine start/stop circuit board and cover
• E) (4) #8 x 3/8" Phillips truss-head screws • F) (6) #4 x 1/2" Phillips pan-head screws • G) (4) Panel clips • H) USB cable
• I) HVAC interface and wiring harness (not shown) • J) Antenna adapter (not shown)
A
B
F
The World's best kits.
®
Ford Mustang
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted charcoal
• Touchscreen display for climate and personalization features
C
D
G
metraonline.com
2015-2017
(with 8" touchscreen)
E
H
© COPYRIGHT 2018 METRA ELECTRONICS CORPORATION
99-5840CH
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . ..............................................2-3
Kit Preparation . ..................................................4-5
Kit Assembly
–ISO DIN radio provision with pocket . .................6
–ISO DDIN radio provision . ....................................6
Axxess Interface installation . ............................7-15
WIRING & ANTENNA CONNECTIONS
Wiring Harness: Axxess interface and
wiring harness included
Antenna Adapter: Included with kit
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" socket wrench • Cutting tool
• Torx T-10 screwdriver
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 8/27/18 INST99-5840CH

Publicidad

Capítulos

Tabla de contenido
loading

Resumen de contenidos para Metra 99-5840CH

  • Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. The World’s best kits. metraonline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/27/18 INST99-5840CH...
  • Página 2: Dash Disassembly

    DASH DISASSEMBLY 1. Open the passenger door and remove 4. Remove the rubber tray cover in front the trim panel from the side of the dash. of the shifter, and then remove the (2) (Figure A) 9/32” screws exposed. (Figure D) 2. Open the glove box and remove the trim 5. Unclip and remove the front side panels from each side of the center console. panel on the right side. (Figure B) (Figure E) 3. Unclip and remove the trim/vent dash 6. Remove the (2) 9/32” screws from each panel. (Figure C) side of the center console. (Figure F) (Figure A) (Figure D) C ontinued on the next page (Figure B) (Figure E) (Figure C) (Figure F) 1.800.221.0932 MetraOnline.com...
  • Página 3 DASH DISASSEMBLY (CONT.) 7. Unclip the shifter trim bezel and slightly Ensure that the vehicle is completely pull it up to clear the center console off before proceeding onto the following (3) steps: removal. 8. Open the center console storage 11. Remove the (4) 9/32” screws securing compartment, unclip the top of the the radio/climate control panel, and then console, and then slide it toward the unclip, unplug, and remove. (Figure I) rear of the vehicle to remove it. 12. Remove the (4) 9/32” screws securing the (Figure G) display screen, then unplug and remove. 9. Remove the plastic tray in front (Figure J) of the shifter. 13. Remove the (4) 9/32” screws securing the 10.
  • Página 4: Kit Preparation

    KIT PREPARATION 1. Cut and remove the shaded area from 3. Remove the rubber button membrane the sub-dash to allow clearance for the from the back of the engine start/stop aftermarket radio. (Figure A) switch panel. (Figure D) From the factory radio/climate control panel: 4. Remove the engine start/stop switch panel. (Figure E) 1. Remove the (10) T-10 Torx screws Remove securing the plastic panel cover to the 5. Press in on the (2) retaining tabs inside shaded area rear of the panel, and then remove. the power outlet to remove the inner (Figure B) portion, and then unsnap the outer ring (Figure A) (Figure D) and cover. (Figure F) 2. Remove the (5) T-10 Torx screws securing the circuit board, and then remove. Continued on the next page (Figure C) (Figure B) (Figure E)
  • Página 5 KIT PREPARATION (CONT.) To the 99-5840CH radio trim panel: 3. Insert the USB cable into the USB slot, through the rear. (Figure C) 1. Attach the engine start/stop switch 4. Attach the (4) panel clips provided. panel, and then the rubber button membrane. (Figure A) (Figure D) 2. Secure the engine start/stop circuit Continue to Kit Assembly board and cover to the switch/cover assembly using the (6) #4 x 1/2” Phillips pan-head screws provided. (Figure B) (Figure A) (Figure C)
  • Página 6: Kit Assembly

    KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets 1. Attach the brackets to the radio using using the (4) #8 x 3/8” Phillips truss-head the screws supplied with the radio. screws provided. (Figure A) (Figure A) 2. Remove the metal DIN sleeve and trim Continue to Axxess ring from the aftermarket radio. Interface Installation 3. Slide the radio into the bracket/pocket assembly, and then secure it using the screws supplied with the radio. (Figure B) (Figure A) (Figure A) Continue to Axxess Interface Installation (Figure B) 1.800.221.0932...
  • Página 7: Tabla De Contenido

    AXXESS INTERFACE INSTALLATION INTERFACE FEATURES TABLE OF CONTENTS Connections ..........................8-9 • Provides accessory power (12-volt 10-amp) Installation ..........................10 • Retains R.A.P. (retained accessory power) Programming ..........................11 • Retains the factory personalization menu and climate controls status Final assembly ..........................11 • Provides NAV outputs (parking brake, reverse, speed sense) Touchscreen display operation ....................12-13 • Retains audio controls on the steering wheel Steering wheel control settings ....................14-15 • Retains the factory backup camera Troubleshooting .......................... 15 • Retains balance • Micro “B” USB updatable INTERFACE COMPONENTS TOOLS REQUIRED • Axxess interface (built into the touchscreen display)
  • Página 8: Connections

    CONNECTIONS From the 16-pin harness with stripped leads to the aftermarket radio: From the 5840 harness to the aftermarket radio: • Connect the Red wire to the accessory wire. • Connect the Black wire to the ground wire. • Connect the Blue/White wire to the amp turn on wire. This wire must be connected to hear • Connect the Yellow wire to the battery wire. sound from the factory amplifier. • Connect the Blue wire to the power antenna wire. • If the aftermarket radio has an illumination wire, connect the • Disregard the Red and White RCA jacks labeled “RSE/SYNC/SAT”, they will not be used Orange/White wire to it. in this application. • Connect the Gray wire to the right front positive speaker output. • Disregard the Red and White RCA jacks labeled “FROM 3.5”, they will not be used • Connect the Gray/Black wire to the right front negative speaker output.
  • Página 9 • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/ doubt as to where the 3.5mm jack goes to. White wire of the connector. Then connect the remaining steering wheel control wire, 54-pin backup camera harness: normally Brown/White, to the Brown wire of the connector. There are two different methods for connecting the factory backup camera. • Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire. If retaining the camera to the aftermarket radio is desired: • Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow • Connect the Yellow RCA jack the backup camera input of the aftermarket radio. wire to the Brown wire. If retaining the camera to the touchscreen display is desired: Note: If the Kenwood radio auto detects as a JVC, manually set the radio type to Kenwood. See the instructions under changing radio type.
  • Página 10: Installation

    INSTALLATION It is highly advisable to read the following steps beforehand, to ensure a clear understanding of HVAC interface what is to be expected. The following steps must be done in the order that they are numbered. 6. Connect the HVAC interface harness into the HVAC interface, and then to the With the vehicle completely off: wiring harnesses in the vehicle. These harnesses are the ones removed in step 11 of dash disassembly. Touchscreen display a. Then connect the 10-pin harness into the engine start/stop circuit board assembly. 1. Connect the 16-pin harness with stripped leads into port “B” in the Attention! There are (2) 10-pin connectors, one in the engine start/stop circuit board touchscreen display. assembly, and one in the touchscreen display. Use only the appropriate connector and 2. Connect the 5840 harness to the wiring harnesses in the vehicle. These harnesses are the disregard the other one. If the incorrect port is accidentally used, the vehicle will need to be ones removed in step 13 of dash disassembly. Then insert the 5840 harness into port “A” in reset by removing the battery for a couple minutes.
  • Página 11: Programming

    PROGRAMMING FINAL ASSEMBLY Attention! If the interface loses power for any reason, the following steps will 1. Connect the USB cable attached to the radio trim panel with touchscreen display, to the need to be performed again. USB port in the back of the radio, if applicable. 1. Refer to step 2 from the “Installation” section. 2. Secure the completed assembly into the upper dash using the factory hardware removed in step 12 of dash disassembly. 2. Press the push-to-start button to start the vehicle. 3. Snap the radio trim panel with touchscreen display over the completed assembly, and then 3. Program the kit: reassemble the dash in reverse order of disassembly.
  • Página 12: Touchscreen Display Operation

    TOUCHSCREEN DISPLAY OPERATION HVAC Control screen • This is the HVAC control screen which will be displayed on the touchscreen display. This is considered the main screen. • The upper left tab with (3) arrows will take you to the Heated/Cooled Seats screen. Note: This screen will also include Heated Steering. • The upper right tab with the gear icon will take you to the Configuration Settings screen. • The climate controls will function in the same manner that they did with the factory climate controls. Continued on the next page 1.800.221.0932 MetraOnline.com...
  • Página 13: System Configuration

    TOUCHSCREEN DISPLAY OPERATION (CONT.) Configuration Settings screen • Steering Wheel Controls • Remap Buttons – For remapping the steering wheel control buttons • Dual Assign – For dual assigning the steering wheel control buttons (long button press) • Select Radio – For auto detecting the radio, or changing the radio type • System Configuration • About - Information regarding the software in the kit • Temperature Unit - To change between Celsius and Fahrenheit • Backlight • Digital Amp Gain - For adjusting the output gain to the amplifier • Four slide bars control the color of the buttons and the back-light intensity: • Reset Vehicle Type - To reset the kit to default settings Red / Green / Blue / Backlight • Backup Camera • Enable – Enables the backup camera image to the touchscreen display • Disable – Disables the backup camera image to the touchscreen display (default) REV.
  • Página 14: Steering Wheel Control Settings

    STEERING WHEEL CONTROL SETTINGS Remap Button screen Dual Assign screen • The interface has the ability to change the button assignment for the steering wheel • The interface has the capability to assign two functions to a single button, except control audio buttons, except Volume-Up and Volume-Down. Follow the prompts on the Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to touchscreen display to remap the steering wheel control audio button(s) to your liking. program the button(s) to your liking. Note: The aftermarket radio may not have all of these commands. Please refer to the Note: Seek-Up and Seek-Down come programmed as Preset-Up and Preset-Down manual provided with the radio, or contact the radio manufacturer, for specific commands for a long button press. recognized by that particular radio. Continued on the next page 1.800.221.0932 MetraOnline.com...
  • Página 15: Troubleshooting

    † Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the other Clarion radio type; same for Eclipse. ‡ Note: If you have a Kenwood radio and the touchscreen display shows a JVC radio, change the radio type to Kenwood. • To show which brand radio is “auto detected” to the interface, press the “Autodetect” button. The radio detected will have a filled in circle. If the incorrect radio is shown, select the proper radio. • Following is a list of radio manufacturers that the interface presently acknowledges. TROUBLESHOOTING Others may be added at a later date. Universal “2 or 3 wire” radios can show up as any of these radio manufacturers. Eclipse (Type 1) † Clarion (Type 2) † Parrot ** Resetting the interface 1. With the vehicle running, press the “Reset Vehicle Type” button mentioned in Kenwood ‡ Pioneer/Jensen Metra OE XITE “System Configuration”. Clarion (Type 1) † Alpine * Eclipse (Type 2) † Philips 2. Refer to “Programming”, step 2, from this point. Sony / Dual Visteon Valor REV. 8/27/2018 INST99-5840CH...
  • Página 16 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. metraonline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/27/18 INST99-5840CH...
  • Página 17 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/27/18 INST99-5840CH...
  • Página 18: Desmontaje Del Tablero

    DESMONTAJE DEL TABLERO 1. Abra la puerta del pasajero y quite 4. Quite la cubierta de la charola de caucho el panel de la moldura en el lado del frente a la palanca de velocidades y tablero. (Figura A) luego quite los (2) tornillos de 9/32” que quedan a la vista.
  • Página 19 DESMONTAJE DEL TABLERO (CONT.) 7. Desenganche el bisel de la moldura Asegúrese de que el vehículo esté de la palanca de velocidades y jálela completamente apagado antes de pasar a los siguientes (3) pasos: ligeramente hacia arriba para poder quitar la consola central. 11.
  • Página 20: Preparación Del Kit

    PREPARACIÓN DEL KIT 1. Corte y quite el área sombreada del sub 3. Quite la membrana del botón de tablero para hacer espacio para el radio caucho de la parte trasera del panel del de mercado secundario. (Figura A) interruptor de encendido/apagado del motor.
  • Página 21 PREPARACIÓN DEL KIT (CONT.) Al panel de la moldura del radio 99-5840CH: 3. Inserte el cable USB en la ranura USB, por la parte trasera. (Figura C) 1. Una la moldura de encendido/apagado 4. Conecte los (4) ganchos para panel del motor, panel del interruptor de suministrados.
  • Página 22: Ensamble Del Kit

    ENSAMBLE DEL KIT Provisión de radio ISO DIN con cavidad Provisión de radio ISO DDIN 1. Coloque los soportes del radio usando 1. Sujete la cavidad a los soportes del radio los tornillos que vienen con el radio. usando los (4) tornillos Phillips #8 de 3/8” (Figura A) de cabeza segmentada suministrados.
  • Página 23: Instalación De La Interfaz Axxess

    INSTALACIÓN DE LA INTERFAZ AXXESS INSTALACIÓN DE LA INTERFAZ AXXESS INDICE • Provee corriente de accesorio (12 voltios 10 amperes) Conexiones ............................8-9 Instalación .............................. 10 • Retiene R.A.P. (corriente de accesorio retenida) Programación ............................11 • Retiene el menú de personalización de fábrica y el estado de los controles de clima Ensamble final ............................
  • Página 24: Conexiones

    CONEXIONES Del arnés de 16 pins con conectores pelados al radio de mercado secundario: Desde el arnés 5840 al radio de mercado secundario: • Conecte el cable rojo al cable de accesorios. • Conecte el cable negro al cable de tierra. •...
  • Página 25 Existen dos métodos distintos para conectar la cámara de reversa de fábrica. • Equipo original Metra: Conecte el cable Key 1 (gris) del control en el volante al cable marrón. Si se desea retener la cámara al radio de mercado secundario: •...
  • Página 26: Instalación

    Este arnés es el que se retira del paso 12 en el desmontaje del tablero. 9. Localice el conector de la antena de fábrica en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de un adaptador adecuado de acoplamiento de Metra.
  • Página 27: Programación

    PROGRAMACIÓN ENSAMBLE FINAL ¡Atención! Si la interfaz pierde la alimentación por cualquier motivo, deberá realizar los 1. Conecte el cable USB unido al panel de la moldura del radio con la pantalla táctil al puerto siguientes pasos de nuevo. USB en la parte trasera del radio, en su caso. 1.
  • Página 28: Operación De La Pantalla Táctil

    OPERACIÓN DE LA PANTALLA TÁCTIL Pantalla de control HVAC • Esta es la pantalla de control HVAC que se mostrará en la pantalla táctil. Esto se considera la pantalla principal. • La pestaña superior izquierda con (3) flechas lo llevará a la pantalla de Asientos con calefacción/enfriamiento, en su caso.
  • Página 29: Luz Posterior

    OPERACIÓN DE LA PANTALLA TÁCTIL (CONT.) Pantalla de Configuraciones: • Controles en el volante • Botones de reubicación: para reubicar los botones del control en el volante • Doble asignación: para doble asignación de los botones de control en el volante (presionar el botón por largo tiempo) •...
  • Página 30: Configuración Del Control En El Volante

    CONFIGURACIÓN DE CONTROL EN VOLANTE Pantalla para reubicar el botón Pantalla de doble asignación • La interfaz tiene la capacidad de cambiar la asignación de botón para los botones de audio del • La interfaz tiene la capacidad de asignar dos funciones a un solo botón, excepto Subir control en el volante, excepto para Subir volumen y Bajar volumen.
  • Página 31: Resolución De Problemas

    Clarion (Tipo 2) † Parrot ** 1. Con el vehículo en funcionamiento, presione el botón “Restablecer tipo de vehículo” Kenwood ‡ Alpine * Metra OE XITE mencionado en “Configuración del sistema”. Clarion (Tipo 1) † Visteon Eclipse (Tipo 2) †...
  • Página 32 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV. 8/27/18 INST99-5840CH...

Tabla de contenido