Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Radio trim panel with touchscreen display • B) Radio brackets • C) SYNC module brackets • D) Pocket • E) Engine start/stop circuit board and cover
• F) Engine start/stop trim • G) (4) #8 x 3/4" Phillips pan-head screws • H) (4) #8 x 3/8" Phillips truss-head screws • I) (6) #4 x 1/2" Phillips pan-head
screws • J) (4) Panel clips • K) USB cable • L) HVAC interface and wiring harness (not shown)
A
B
G
The World's best kits.
®
Ford Mustang
*Visit metraonline.com for up-to-date vehicle specific applications.
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted charcoal
• Touchscreen display for climate and personalization features
C
D
H
I
metraonline.com
2015-up*
(with 4.2" screen)
E
F
J
K
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
99-5838CH
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
Dash Disassembly . ............................................. 2-4
Kit Preparation . ...................................................5-7
Kit Assembly
–ISO DIN radio provision with pocket . .................8
–ISO DDIN radio provision . ....................................8
Axxess Interface installation . ........................... 9-17
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: Axxess interface and
harness included
Antenna Adapter: 40-EU10 (sold separately)
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• 9/32" socket wrench • Cutting tool
• Torx T-10 screwdriver
CAUTION!
All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
REV. 9/28/17 INST99-5838CH
Publicidad
Capítulos
Tabla de contenido
Manuales relacionados para Metra 99-5838CH
Resumen de contenidos para Metra 99-5838CH
- Página 1 Also, do not remove the factory radio with the key in the on position, or while the vehicle is running. The World’s best kits. metraonline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/28/17 INST99-5838CH...
- Página 2 DASH DISASSEMBLY 1. Open the passenger door and remove the trim panel from the side of the dash. (Figure A) 2. Open the glove box and remove the trim panel on the right side. (Figure B) 3. Unclip and remove the trim/vent dash panel. (Figure C) Continued on the next page (Figure A) (Figure B) (Figure C) 1.800.221.0932 MetraOnline.com...
- Página 3 DASH DISASSEMBLY (CONT.) 4. Remove the rubber tray cover in front of the shifter, and then remove the (2) 9/32” screws exposed. (Figure D) 5. Unclip and remove the front side panels from each side of the center console. (Figure E) 6. Remove the (2) 9/32” screws from each side of the center console. (Figure F) C ontinued on the next page (Figure F) (Figure D) (Figure E) REV. 9/28/2017 INST99-5838CH...
- Página 4 DASH DISASSEMBLY (CONT.) 7. Unclip the shifter trim bezel and slightly Ensure that the vehicle is completely pull it up to clear the center console off before proceeding onto the following (4) steps: removal. 8. Open the center console storage 11. Remove the (4) 9/32” screws securing compartment, unclip the top of the the radio/climate control panel, and then console, and then slide it toward the unclip, unplug, and remove. (Figure I) rear of the vehicle to remove it. 12. Remove the (4) 9/32” screws securing the (Figure G) display screen, then unplug and remove. 9. Remove the plastic tray in front (Figure J) of the shifter. 13. Remove the (4) 9/32” screws securing the 10.
- Página 5 KIT PREPARATION 1. Cut and remove the shaded area from the sub-dash to allow clearance for the aftermarket radio. (Figure A) If SYNC is desired to be retained: 2. Attach the SYNC module brackets to the factory SYNC module using the (4) #8 x 3/4” Phillips pan-head screws provided. (Figure B) Remove 3. Re-connect all factory connectors back Note orientation shaded area of arrow into the SYNC module, and then secure the module into the lower sub-dash (Figure A) (Figure B) (Figure C) using the factory hardware removed in step 13. (Figure C) Continued on the next page REV.
- Página 6 KIT PREPARATION (CONT.) From the factory radio/climate control panel: 3. Remove the rubber button membrane from the back of the engine start/stop 1. Remove the (15) T-10 Torx screws securing switch panel. (Figure C) the plastic panel cover to the rear of the 4. Remove the engine start/stop switch panel, and then remove. (Figure A) panel. (Figure D) 2. Remove the (7) T-10 Torx screws securing the circuit board, and then remove. 5. Press in on the (2) retaining tabs inside (Figure B) the power outlet to remove the inner (Figure C) portion, and then unsnap the outer ring and cover. (Figure E) Continued on the next page (Figure A) (Figure D) (Figure E) (Figure B) 1.800.221.0932...
- Página 7 KIT PREPARATION (CONT.) 3. Insert the USB cable into the USB slot, To the 99-5838CH radio trim panel: through the rear. (Figure C) 1. Attach the engine start/stop trim, 4. Attach the (4) panel clips provided. engine start/stop switch panel, and then the rubber button membrane. (Figure D) (Figure A) Continue to Kit Assembly 2. Secure the engine start/stop circuit board and cover to the switch/cover assembly using the (6) #4 x 1/2” Phillips pan-head screws provided. (Figure B) (Figure A) (Figure C) (Figure B) (Figure D) REV. 9/28/2017 INST99-5838CH...
- Página 8 KIT ASSEMBLY ISO DIN radio provision with pocket ISO DDIN radio provision 1. Attach the pocket to the radio brackets 1. Attach the brackets to the radio using using the (4) #8 x 3/8” Phillips truss-head the screws supplied with the radio. screws provided. (Figure A) (Figure A) 2. Remove the metal DIN sleeve and trim Continue to Axxess ring from the aftermarket radio. Interface Installation 3. Slide the radio into the bracket/pocket assembly, and then secure it using the screws supplied with the radio. (Figure B) (Figure A) (Figure A) Continue to Axxess Interface Installation (Figure B) 1.800.221.0932...
-
Página 9: Tabla De Contenido
AXXESS INTERFACE INSTALLATION INTERFACE FEATURES TABLE OF CONTENTS • Provides accessory power (12-volt 10-amp) Connections to be made ......................10-12 Installing the interface ......................12-13 • Retains R.A.P. (retained accessory power) Initializing the interface ......................13 • Provides NAV outputs (parking brake, reverse, speed sense) Final assembly ..........................13 • Retains audio controls on the steering wheel Extra features (SYNC)........................13 • Retains SYNC Touchscreen display operation ....................14-15 • Retains the factory backup camera Steering wheel control settings ....................16-17 • Retains balance and fade • Micro “B” USB updatable TOOLS REQUIRED • Wire cutter • Crimp tool • Solder gun • Tape INTERFACE COMPONENTS • Connectors (example: butt-connectors, bell caps, etc.) • Axxess interface (built into the touchscreen display) -
Página 10: Connections To Be Made
CONNECTIONS TO BE MADE From the 16-pin harness with stripped leads to the aftermarket radio: From the 5838 harness to the aftermarket radio: • Connect the Red wire to the accessory wire. • Connect the Black wire to the ground wire. • If the aftermarket radio has an illumination wire, connect the Orange/White wire to it. • Connect the Yellow wire to the battery wire. • Connect the Gray wire to the right front positive speaker output. • Connect the Blue wire to the power antenna wire. • Connect the Gray/Black wire to the right front negative speaker output. • Connect the Green wire to the left rear positive speaker output. • Connect the Green/Black wire to the left rear negative speaker output. • Connect the White wire to the left front positive speaker output. - Página 11 • Eclipse: Connect the steering wheel control wire, normally Brown, to the Brown/ 12-pin backup camera harness: White wire of the connector. Then connect the remaining steering wheel control wire, There are two different methods for connecting the factory backup camera. normally Brown/White, to the Brown wire of the connector. If retaining the camera to the aftermarket radio is desired: • Metra OE: Connect the steering wheel control Key 1 wire (Gray) to the Brown wire. • Connect the Yellow RCA jack the backup camera input of the aftermarket radio. • Kenwood or select JVC with a steering wheel control wire: Connect the Blue/Yellow wire to the Brown wire. If retaining the camera to the touchscreen display is desired: Note: If the Kenwood radio auto detects as a JVC, manually set the radio type to • Connect the Yellow RCA jack, to the Yellow RCA jack from the 4-pin harness with yellow Kenwood. See the instructions under changing radio type.
-
Página 12: Installing The Interface
2. Connect the 5838 harness to the wiring harnesses in the vehicle. These harnesses are and one in the touchscreen display. Use only the appropriate connector and disregard the the ones removed in step 13 of dash disassembly. Then insert the 5838 harness into port other one. If the incorrect port is accidentally used, the vehicle will need to be reset by “A” in the touchscreen display. But do not install this harness until exactly before step 1 of removing the battery for a couple minutes. “Initializing the Interface”. This is a timed process. Note: Disregard the 4-pin flat to 4-pin stacked harness, it will not be used in this application. 3. Connect the 4-pin harness with yellow RCA jacks into port “C” in the touchscreen display. 7. Then connect the 6-pin harness from the 5838 harness in the HVAC interface. 4. Disregard ports “D” and “E”, they will not be used in this application. 8. Connect the 12-pin backup camera harness, to the wiring harness in the vehicle. This harness 5. Port “F” is an update port for future firmware upgrades. is the one removed in step 12 of dash disassembly. 9. Locate the factory antenna connector in the dash and complete all necessary connections to the radio. Metra recommends using the proper mating adapter from Metra. Continued on the next page 1.800.221.0932 MetraOnline.com... -
Página 13: Initializing The Interface
2. Secure the completed assembly into the upper dash using the factory hardware removed in step 12 of dash disassembly. 2. Press the push-to-start button to start the vehicle. 3. Snap the radio trim panel with touchscreen display over the completed assembly, and then 3. Program the kit: reassemble the dash in reverse order of disassembly. a. Once the touchscreen display loads up, select the vehicle type; “Ford Mustang 2015-2016”. b. Wait until the radio comes on, and the touchscreen display shows EXTRA FEATURES “SWC Configured”. This process may take up to 3 minutes. Note: If the touchscreen display does not load up, or the radio doesn’t come on within 3 minutes, and/or the touchscreen display does not show “SWC Configured”, turn the vehicle SYNC: off and disconnect the 5838 harnesses from port “A” in the touchscreen display. Check all If the vehicle is equipped with SYNC, the 99-5838CH can retain this feature. the connections, reconnect the harness into the touchscreen display, and then try again. • Change the source of the radio to AUX-IN. 4. Test all functions of the installation for proper operation, before reassembling the dash. • Press the “Info” button on the touchscreen display to enter the SYNC menu. Press the “HVAC” button to get back to the main menu. REV. 9/28/2017 INST99-5838CH... -
Página 14: Touchscreen Display Operation
TOUCHSCREEN DISPLAY OPERATION HVAC Control screen Touchscreen calibration: • Press and hold the upper two soft buttons on either side of the touchscreen for 10 seconds. • A screen will pop up asking for you to press the target in the screen. • After pressing the target with your finger, the calibration process will be complete, and the screen will disappear. Continued on the next page • This is the HVAC control screen which will be displayed on the touchscreen display. This is considered the main screen. • Disregard the upper left tab with (3) arrows, it will not be used in this application. • The upper right tab with the gear icon will take you to the Configuration Settings screen. • The climate controls will function in the same manner that they did with the factory climate controls, yet via touchscreen buttons instead. The temperature control will display a numerical scale, with “LO” being the coldest, and “HI” being the hottest: LO / 1-9 / HI Note: The “Info” button will only be shown if SYNC is to be retained. 1.800.221.0932 MetraOnline.com... - Página 15 TOUCHSCREEN DISPLAY OPERATION (CONT.) Configuration Settings screen • Steering Wheel Controls • Remap Buttons – For remapping the steering wheel control buttons • Dual Assign – For dual assigning the steering wheel control buttons (long button press) • Select Radio – For auto detecting the radio, or changing the radio type • System Configuration • Firmware version • Backlight • Four slide bars control the color of the buttons and the back-light intensity: Red / Green / Blue / Backlight • Backup Camera • Enable – Enables the backup camera image to the touchscreen display • Disable – Disables the backup camera image to the touchscreen display (default) REV. 9/28/2017 INST99-5838CH...
-
Página 16: Steering Wheel Control Settings
** Note: The AX-SWC-PARROT is required (sold separately). Also, the Parrot radio must be updated to rev. 2.1.4 or higher through www.parrot.com. † Note: If you have a Clarion radio and the steering wheel controls do not work, change the radio type to the other Clarion radio type; same for Eclipse. ‡ Note: If you have a Kenwood radio and the touchscreen display shows a JVC radio, change the radio type to Kenwood. • To show which brand radio is “auto detected” to the interface, press the “Autodetect” button. The radio detected will have a filled in circle. If the incorrect radio is shown, Continued on the next page select the proper radio. • Following is a list of radio manufacturers that the interface presently acknowledges. Others may be added at a later date. Universal “2 or 3 wire” radios can show up as any of these radio manufacturers. Eclipse (Type 1) † Clarion (Type 2) † Parrot ** Kenwood ‡ Pioneer/Jensen Metra OE XITE Clarion (Type 1) † Alpine * Eclipse (Type 2) † Philips Sony / Dual Visteon Valor 1.800.221.0932 MetraOnline.com... - Página 17 STEERING WHEEL CONTROL SETTINGS (CONT.) Remap Button screen Dual Assign screen • The interface has the ability to change the button assignment for the steering wheel • The interface has the capability to assign two functions to a single button, except control audio buttons, except Volume-Up and Volume-Down. Follow the Volume-Up and Volume-Down. Follow the prompts on the touchscreen display to program prompts on the touchscreen display to remap the steering wheel control audio button(s) the button(s) to your liking. to your liking. Note: Seek-Up and Seek-Down come programmed as Preset-Up and Preset-Down Note: The aftermarket radio may not have all of these commands. Please refer to the for a long button press. manual provided with the radio, or contact the radio manufacturer, for specific commands recognized by that particular radio. REV. 9/28/2017 INST99-5838CH...
- Página 18 ASWC PROGRAMMING (SOLD SEPARATELY) 1.800.221.0932 MetraOnline.com...
- Página 19 REV. 9/28/2017 INST99-5838CH...
- Página 20 Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians The World’s best kits. metraonline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/28/17 INST99-5838CH...
- Página 21 Además, no quite el radio de fábrica con la llave en la posición o de encendido ni con el vehículo funcionando. The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/28/17 INST99-5838CH...
- Página 22 DESMONTAJE DEL TABLERO 1. Abra la puerta del pasajero y quite el panel de la moldura en el lado del tablero. (Figura A) 2. Abra la guantera y quite el panel de la moldura en el lado derecho. (Figura B) 3.
- Página 23 DESMONTAJE DEL TABLERO (CONT.) 4. Quite la cubierta de la charola de caucho frente a la palanca de velocidades y luego quite los (2) tornillos de 9/32” que quedan a la vista. (Figura D) 5. Desenganche y quite los paneles laterales frontales de cada lado de la consola central.
- Página 24 DESMONTAJE DEL TABLERO (CONT.) 7. Desenganche el bisel de la moldura Asegúrese de que el vehículo esté de la palanca de velocidades y jálela completamente apagado antes de pasar a los siguientes (3) pasos: ligeramente hacia arriba para poder quitar la consola central. 11.
- Página 25 PREPARACIÓN DEL KIT 1. Corte y quite el área sombreada del sub tablero para hacer espacio para el radio de mercado secundario. (Figura A) Si se desea retener SYNC: 2. Sujete los soportes del módulo SYNC al módulo SYNC de fábrica usando los (4) tornillos Phillips #8 de 3/8”...
- Página 26 PREPARACIÓN DEL KIT (CONT.) Del panel del radio/control del clima de 4. Quite el panel del interruptor de fábrica: encendido/apagado del motor. (Figura D) 1. Quite los (15) tornillos Torx T-10 sujetando la cubierta del panel de 5. Oprima hacia adentro en las (2) plástico a la parte trasera del panel y pestañas de retención dentro de la luego quite.
- Página 27 PREPARACIÓN DEL KIT (CONT.) 3. Inserte el cable USB en la ranura USB, Al panel de la moldura del radio 99-5838CH: por la parte trasera. (Figura C) 1. Una la moldura de encendido/apagado 4. Conecte los (4) ganchos para panel del motor, panel del interruptor de suministrados.
- Página 28 ENSAMBLE DEL KIT Provisión de radio ISO DIN con cavidad Provisión de radio ISO DDIN 1. Coloque los soportes del radio usando 1. Sujete la cavidad a los soportes del radio los tornillos que vienen con el radio. usando los (4) tornillos Phillips #8 de 3/8” (Figura A) de cabeza segmentada suministrados.
- Página 29 INSTALACIÓN DE LA INTERFASE AXXESS INSTALACIÓN DE LA INTERFAZ AXXESS INDICE • Provee corriente de accesorio (12 voltios 10 amperes) Conexiones que se deben hacer ....................10-12 Instalación de la interfaz ......................12-13 • Retiene R.A.P. (corriente de accesorio retenida) Inicializar la interfaz ........................13 •...
-
Página 30: Conexiones Que Se Deben Hacer
CONEXIONES QUE SE DEBEN HACER Del arnés de 16 pins con conectores pelados al radio de mercado secundario: Desde el arnés 5838 al radio de mercado secundario: • Conecte el cable negro al cable de tierra. • Conecte el cable rojo al cable de accesorios. •... - Página 31 Existen dos métodos distintos para conectar la cámara de reversa de fábrica. • Equipo original Metra: Conecte el cable Key 1 (gris) del control en el volante al cable marrón. Si se desea retener la cámara al radio de mercado secundario: •...
-
Página 32: Instalación De La Interfaz
Este arnés es el que se retira del paso 12 en el desmontaje del tablero. 9. Localice el conector de la antena de fábrica en el tablero y realice todas las conexiones necesarias al radio. Metra recomienda el uso de un adaptador adecuado de acoplamiento de Metra. -
Página 33: Inicializar La Interfaz
“SWC Configured”, apague el vehículo y desconecte los Si el vehículo está equipado con SYNC, el 99-5838CH puede conservar esta función. arneses 5838 del puerto “A” en la pantalla táctil. Revise todas las conexiones, vuelva a conectar el arnés a la pantalla táctil e inténtelo de nuevo. -
Página 34: Operación De La Pantalla Táctil
OPERACIÓN DE LA PANTALLA TÁCTIL Pantalla de control HVAC Calibración táctil: • Oprima y sostenga los dos botones superiores suaves en cualquier lado de la pantalla táctil por 10 segundos. • Aparecerá una ventana emergente pidiéndole que oprima el objeto en la pantalla. - Página 35 OPERACIÓN DE LA PANTALLA TÁCTIL (CONT.) Pantalla de Configuraciones • Controles en el volante • Botones de reubicación: para reubicar los botones del control en el volante • Doble asignación: para doble asignación de los botones de control en el volante (oprimir el botón por largo tiempo) •...
-
Página 36: Configuración Del Control En El Volante
Eclipse (Tipo 1) † Pioneer/Jensen Clarion (Tipo 2) † Parrot ** Kenwood ‡ Alpine * Metra OE XITE Clarion (Tipo 1) † Visteon Eclipse (Tipo 2) † Philips Sony / Dual Valor 1.800.221.0932... - Página 37 CONFIGURACIÓN DE CONTROL EN VOLANTE (CONT.) Pantalla para reubicar el botón Pantalla de doble asignación • La interfaz tiene la capacidad de cambiar la asignación de botón para los botones de audio del • La interfaz tiene la capacidad de asignar dos funciones a un solo botón, excepto Subir control en el volante, excepto para Subir volumen y Bajar volumen.
- Página 38 1.800.221.0932 MetraOnline.com...
- Página 39 REV. 9/28/2017 INST99-5838CH...
- Página 40 800-354-6782 for more information and take steps www.installerinstitute.com o llame al toward a better tomorrow. 800-354-6782 para obtener más información y avance hacia un futuro mejor. Metra recomienda MECP Técnicos certificados The World’s best kits. MetraOnline.com ® © COPYRIGHT 2017 METRA ELECTRONICS CORPORATION REV. 9/28/17 INST99-5838CH...