Preparation For Use; Service - DRESTER Boxer quattro Combo DB44C Manual De Operación

PREPARATIONS FOR USE
Remove the front panel (item 5 illustration 1) by lifting it up-
and-out.
Remove the foot-pedal console (items 6 illustration 1) by lifting
it up and folding it out to the side (see illustration 2).
Solvent drums for the left side of the unit:
Two drums are needed, one drum that is
of solvent.
full Both drums must be of the same size,
must meet the requirements described under chapter PERMIT-
TED SOLVENT DRUMS. Both drums must be clean on the inside
and they must not contain any solids or other objects that
could be sucked into the pumps when running.
Drum plugs
There are several types of solvent drums on the market, each
with different diameter of the opening. With the unit, a card-
board box with a selection of tapered plugs is supplied (see
illustration 3). Select the plug that fi t well into the opening of
the drums, and fi t them onto the drum adaptor of the hoses
(see illustration 4).
Solvent fi ll-up on the left side of the unit:
Use one empty drum and another drum of the same size full of
clean solvent.
Place the empty drum underneath the unit (item 2 illustration
2). Insert the group of hoses containing the drain hose from the
sink into this drum (item 4 illustration 2). Make sure that the
hoses are properly led well down into the drum, and that the
opening is well sealed by the tapered plug.
Take the second drum, the one full of solvent, and pour half of
its contents directly into the gun cleaner's sink (item 2A illustra-
tion 1). The solvent that is poured in will drain into the drum
underneath the gun cleaner. Make sure to have the ventilation
running during this procedure.
Place the second drum, now half full, on the fl oor by the fi rst
drum (item 3 illustration 2). Insert the second group of hoses
containing a white hose into this drum (item 5 illustration 2).
Make sure that the hoses are properly led into the drum all the
way down to the bottom, and that the opening is well sealed
by the tapered plug.
The solvent system for the left side uf the unit is now fi lled-up.
Both drums should be half full. The fi rst drum connected to the
drain hose from the sink , contains the solvent that will be re-
circulating for the automatic wash cycle, and the second drum
connected to the white hose contains clean solvent for rinsing.
The contents of the right drum will gradually be used up and
transferred to the left drum.
16015 rev 2014-11-06
Solvent drum with water based solvent for the right
side of the unit:
Place the drum underneath the unit (item 14 illustration 2).
Insert the group of hoses containing the drain hose from the
automatic washer on the right side into this drum (item 16
illustration 2). Make sure that the hoses are properly led well
down into the drum, and that the opening is well sealed by the
tapered plug.
, and one drum
empty
and they
Water
Fill the fi ltrate container (item 7 illustration 2) to 1/2 of the
volume with clean water.
Operating instructions
Operating instructions should be formulated on the basis of
this manual and translated into the language spoken by the
employees. It should always be available close to the machine.
To avoid confusion, the employees must be informed about the
solvent currently being used in the machine.

SERVICE

Weekly
– Remove the strainers at the bottom of the automatic
Monthly
– Remove the fi ve nozzles in each automatic washer and
When changing drums
– Check and if necessary clean the strainers on the suction
When changing fi lters
– Check and if necessary clean the strainer on the suction
– Take out the fi ltrate container (item 7 illustration 2) and
Every month
– Change the water completely.
washers (item 2 illustration 5) and clean them.
Do not forget to re-fi t !
clean them with clean solvent. (see illustration 8).
hoses.
pipe (item 15 illustration 2).
empty it completely. Rinse it with water and wipe it off with
cloth or paper.
5