RIB MASTER Wi-Fi FR Manual Del Usuario página 22

G
B
CONNECTION OF THE AUTOTEST INPUT (brown wire A/D+ TEST) for
compliance with standard EN13849-2:2008
- If control panel used is equipped with autotest place jumper JP1 on MASTER
Wi-Fi FR paying attention to the control panel AUTOTEST power supply -
negative or positive/alternate (see relative instructions).
- Connect the auto test output of the control panel to the brown wire of the
MASTER Wi-Fi FR in order to be able to control the system at the end of every
complete automated opening.
- Closing will only occur when the MASTER Wi-Fi FR card has passed the control
test.
- If the MASTER Wi-Fi FR card control test fails, the control panel will block the
automation, the dual-color LED on the MASTER Wi-Fi FR card indicates a safety
outage, alternately flashing red and green.
The buzzer emits an alternating sound for 1 minute to signal the problem.
The alarm status of the buzzer comes on again for 1 minute when a control is
given.
If the panel is not equipped with an auto test, the control test is ignored.
E -
MASTER Wi-Fi FR POWER
After having made all of the connections, provide power to the control panel with
MASTER Wi-Fi FR.
The yellow LED DL6 should come on and the buzzer will emit a sound indicating
correct power.
The LED DL7 will alternately flash red and green indicating that no remote controls
or blinkers have been memorized.
F -
IDENTIFICATION OF SAFETY DEVICES
If control panel has 2 inputs for the different management of the safety edges
TOUCH Wi-Fi and VERTIGO Wi-Fi in opening and closing:
EDGE 1 = yellow wire - safety edge in opening (LED EDGE/PHOT available from
1 to 3)
EDGE 2 = green wire - safety edge in closing (LED EDGE/PHOT available from
4 to 6)
If control panel has 1 input for the management of the safety edges, than connect
just EDGE 1 = yellow wire - safety edge in opening and closing (LED EDGE/PHOT
available from 1 to 3)
Every Wi-Fi safety device must OBLIGATORILY be identified placing only one
of the 6 micro-switches present on its circuit (different for each of the 6 safety
devices) in the ON position. Obviously one pair of photocells is considered one
safety device and must therefore have a receiver and transmitter with the same
DIP in the ON position.
IDENTIFY THE CONTAINERS OF THE SAFETY DEVICES WITH THE
NUMBER OF THE ACTIVATED MICRO-SWITCH AND ATTACH THE
NUMBERED ADHESIVE STRIP SUPPLIED TO THE OUTSIDE OF EACH
CONTAINER.
The adhesive strip serves as a means of quickly identifying the safety device
when it needs maintenance.
Note: Each safety device is supplied with the micro-switches in the OFF position
so that battery power is not consumed when not in use (if inserted).
Insert the batteries in the Wi-Fi safety devices.
G -
MEMORIZATION OF THE SAFETY DEVICES
After having performed the identification of the safety devices, and provided power
with the batteries, place the micro-switches with the same number of the safety
devices on the MASTER Wi-Fi FR in the ON position to activate the safety
devices to be memorized.
Use the following procedure for memorization:
- Push the button PROG RX on the MASTER Wi-Fi FR => dual-color LED
EDGE PHOT 1 flashes red for 1 minute (the time needed for memorization).
- Push the button PROG TX on the safety device with micro-switch 1 in the ON
position => on the MASTER Wi-Fi FR the dual-color LED EDGE PHOT 1 flashing
red turns green and a sound from the buzzer indicates that the safety device
has been memorized correctly, immediately the dual-color LED EDGE PHOT 2
begins flashing red.
- If there are no other safety devices to be memorized after one minute the
dual-color LED EDGE PHOT 2will turn off or, push the button PROG. RX 4
times to end the memorization procedure => all of the dual-color LED EDGE
PHOT should be off.
MEMORIZATION OF OTHER SAFETY DEVICES
- After having memorized the first safety device, the dual-color LED EDGE
PHOT 2 automatically begins flashing red for 1 minute (the time needed for
memorization).
- Push the button PROG. TX on the safety device with micro-switch 2 in the
ON position => on the MASTER Wi-Fi FR the dual-color LED EDGE PHOT 2
flashing red turns green and a sound from the buzzer indicates that the safety
device has been memorized correctly.
- Follow the same procedure for any other safety devices (up to a maximum
of 6).
ADDING OTHER SAFETY DEVICES (UP TO 6 TOTAL)
If after installation the use of further safety devices (PHOTOCELLS OR STRIPS)
is desired, to increase door safety, it is recommended to:
- Turn off power to the door.
- Place the safety device in the desired position and identify it by moving the
internal micro-switch.
- Perform the programming by setting to ON a micro-switch different from that of
the other safety devices installed and identify it with the corresponding numbered
adhesive strip (see paragraph F – IDENTIFICATION OF Wi-Fi SAFETY
DEVICES).
- Enable the micro-switch of the safety device just added on the MASTER Wi-Fi
FR card.
- Return power to the door.
- Follow the memorization procedure and system check as indicated previously.
NOVA Wi-Fi AND VERTIGO Wi-Fi PHOTOCELLS SYSTEM CHECK
- Check that the micro-switch selected on the transmitter TX NOVA Wi-Fi is the
same as that selected on the receiver RX NOVA Wi-Fi (example 1 ON).
- Proper function of the TX NOVA Wi-Fi is shown by the green LED which comes
on for 10 seconds.
- Push and release the button S3 "PROG. TX" on the NOVA Wi-Fi receiver (it
activates for 3 minutes to perform the alignment procedure). If the photocells are
already aligned the red LED emits a constant light. If the red LED is off or emits
a flashing light, perform the alignment until it emits a constant light.
22
22
-
JP1
+/~
JP1