RIB MASTER Wi-Fi FR Manual Del Usuario página 24

G
B
- After 10 seconds the dual-color LED EDGE PHOT flashes alternately red and
green 6 times, indicating successful removal.
ATTENTION: Place the micro-switch corresponding to the eliminated safety device
in the OFF position, then scan the dual-color LED pushing the button PROG. RX
6 times. IMPORTANT: Remove the batteries from the eliminated safety device.
H -
PROGRAMMING THE SPARK Wi-Fi BLINKER
- Push and hold the button PROG. RX on the MASTER Wi-Fi FR for at least 3
seconds.
- After releasing the button PROG. RX the dual-color LED DL7 will begin flashing
red for 10 seconds.
- Push the button S4 PROG. TX on the SPARK Wi-Fi blinker to send a radio signal
to the MASTER Wi-Fi FR.
- Successful memorization is indicated by a sound from the buzzer and the red
dual-color LED DL7 on the MASTER Wi-Fi FR turning green, while the red LED
DL7 on the SPARK Wi-Fi card flashes 3 times.
- Allow 10 seconds to pass to conclude programming, or push button PROG. RX
on the MASTER Wi-Fi FR for a moment.
- Replace the casing.
- Mount the diffuser and attach it with the screws provided.
More than one blinker can be memorized by the MASTER Wi-Fi FR.
Each SPARK Wi-Fi blinker receives during the memorization one single identic
code from the MASTER Wi-Fi FR to which it is paired up.
When the MASTER Wi-Fi FR is activated by a command, all SPARK Wi-Fi
blinkers memorized in it will start blinking simoultanesly.
SYSTEM CHECK
Give a command to the door and check that the SPARK Wi-Fi blinker flashes
correctly.
P
ROGRAMMING REMOTE CONTROLS, BLOCK Wi-Fi KEY
SELECTOR and RADIO NUMERIC CODER FOR TOTAL OPENING
(maximum of 100 codes)
Using the following procedure it is possible for MASTER Wi-Fi FR to memorize
the following remote controls:
SUN DUAL-CHANNEL 433 MHz
SUN FOUR-CHANNEL 433 MHz
SUN CLONE DUAL-CHANNEL 433 MHz
SUN CLONE FOUR-CHANNEL 433 MHz
BLOCK Wi-Fi KEY SELECTOR 433 MHz
RADIO NUMERIC CODER to embed
RADIO NUMERIC CODER to wall
At MASTER Wi-Fi FR start-up the yellow LED DL6 will turn on.
- At the same time the buzzer will emit a sound indicating proper power status.
a - If the MASTER Wi-Fi FR memory is empty (standard version) the dual-color
LED DL7 flashes alternately red and green.
a - If codes are already present in the memory, the dual-color LED DL7 remains
off (perform a total removal - see paragraph TOTAL CODE REMOVAL
PROCEDURE).
- Push and hold the button PROG RX for at least 3 seconds. After release the
dual-color LED DL7 on the MASTER Wi-Fi FR flashes red for 10 seconds. At
this time pressing one of the buttons on the transmitter will memorize the code.
- In addition to the codes, MASTER Wi-Fi FR also learns the channels that
are desired for use. Be careful to remember the buttons pushed on the
remote controls during the code memorization procedure as they will be
those used thereafter for the total opening.
- If no code is sent, after 10 seconds the red dual-color LED DL7 on the MASTER
Wi-Fi FR turns off indicating the end of the programming procedure. The dual-
color LED DL7 flashes alternately red and green indicating that there are no
codes in the memory.
- Successful code memorization is shown by the dual-color LED DL7 emitting
a green light for 500ms and by a sound from the buzzer, indicating successful
memorization.
- After memorizing the first code, the memorization time resets for 10 seconds and
it is possible to memorize more codes.
- To finish the code memorization procedure, allow 10 seconds to pass until
the flashing red LED DL7 turns off. Alternatively, push button PROG RX on
the MASTER Wi-Fi FR, also in this case the flashing red LED DL7 turns off,
indicating the end of the memorization procedure.
With the dual-color DL7 off, the MASTER Wi-Fi FR is ready to work.
Push a button of a previously memorized remote control. The green LED DL7 on
the MASTER Wi-Fi FR comes on for a moment, indicating recognition of a valid
code. After 2 second led DL5 comes on for a moment, at the same time, total
opening is ordered.
Note: If, when pushing a button on the remote control, the dual-color LED DL7
turns red for a moment, this means that the button/code is not in the memory and
you must therefore perform the memorization procedure again.
T
OTAL CODE REMOVAL PROCEDURE
- Position jumper JP2 as shown here:
- Push and release button PROG RX on the MASTER Wi-Fi FR. The dual-color
LED DL7 emits a red light for 0.5 sec. and then turns off, indicating successful
removal of codes and start-up information..
- Position jumper JP2 as shown here:
- The LED DL7 begins flashing alternately red and green, indicating that the
memory is empty.
Note: Jumper JP2 during normal operation must be positioned as shown here:
F
ULL MEMORY SIGNAL
If, when pushing and holding button PROG RX on the MASTER Wi-Fi FR for at
least 3 seconds, upon release the dual-color LED DL7 flashes green 6 times, this
means that the memory is full (maximum 100 codes).
Code ACG6052
Code ACG6054
Code ACG6056
Code ACG6058
Code ACG6098
Code ACG9434
Code ACG9436
TO download the video of the installation write the following
address in your browser, or, read the QR code with your
smartphone:
http://www.youtube.com/user/RIBSRL?feature=mhee
24
24