Nice O-Box Instrucciones Y Advertencias Para El Uso página 13

grammable manually on the receiver that hosts this memory.
J Timer: enables modifications to the timer time intervals. The time is dis-
played in hours minutes and seconds.
J Altera: this is a code that enables personalisation of a receiver; this code
is compatible with the previous systems "FloR".
Caution! – Do not forget the new protection code otherwise the receiver will
no longer be usable.
J RND control: enables the user to enable or disable control of the variable
section of the identity code (RND) of a receiver.
J RND window: enables modifications to the RND window of a receiver.
This window represents the portion of values within which the variable sec-
tion of the identity (RND) code is accepted.
Note – Normally the window value is 100 and may have a value from 5 to
250.
J Synchronism: enables the user to activate or deactivate the receiver re-
synchronisation. If synchronism is deactivated, system safety is increased,
but if the transmitter exits the RND window, the identity code will have to be
memorised again in the receiver memory.
J Native only: enables the user to enable or disable the receiver for recep-
tion of commands sent by a transmitter with a code modified with respect to
factory settings.
NiceOne RECEIVERS
The functions available are:
• Certificates: this function enables reading and entry of receiver certificates
(up to a maximum of 4). In order, starting from the top, the receiver certificate
(present on the card in the pack) is listed, followed by 3 spaces usable to cre-
ate groups of receivers.
Note – For more information on use of certificates, refer to the manual "Nice
Opera System Book".
• Codes: this function enables the user to personalise a receiver, with the
option to modify the codes of "Installer", "Installation" and "Altera". In particular,
"Altera" is compatible with the previous systems "FloR".
Caution! – Do not forget the new protection code otherwise the receiver will no
longer be usable.
The codes are useful to personalise a system: in other words the original code
(factory setting) of a transmitter can be modified if required. For this reason the
codes must be the same on the transmitter and the receiver. In this case the O-
Box codes must also be modified to enable subsequent use.
• Advanced settings: This function enables entry of the following parameters.
J Basic settings
- Enable original TX only: this function enables the user to enable or disable
operation of a receiver that receives the command from transmitters with a
modified code, i.e. with a code that is no longer the factory-set value.
- Disable RND: this function enables the user to enable or disable control of
the variable section of the identity code (RND) of a receiver.
J Memorisation settings
- Memorisation lock by means of "Enable code": this function enables the
user to lock memorisation of a new transmitter using the "Enable code" of an
old transmitter (already memorised). This procedure may be used only if two
transmitters with "O-Code" encoding are used.
- Memorisation lock by means of "Certificate": this function enables the
user to lock memorisation of a new transmitter using the certificate of a
receiver.
- Remote memorisation lock: this function enables the user to lock memo-
risation of a new transmitter using an old transmitter with the procedure "in
the vicinity of transmitter"
J BUS T4 settings
Note - The "Bus" is a system that enables connection of all automation sys-
tem devices, using a single cable with several internal electrical wires. In this
type of connection, data communication between devices is via a specific
protocol, which in this case is the Nice "Bus T4".
- Enable code repetition via bus: this function enables the user to enable
the option on a receiver to transfer the copy of a code received via radio from
a transmitter, to other connected devices, by means of the Bus T4 cable.
- Enable code reception via bus: this function enables the user to enable
the option on a receiver to receive a code transmitter via the Bus T4 cable by
another receiver (refer to the point above "Enable code repetition via bus").
- Enable authorisation groups: This function enables the user to enable
management of radio codes in specific authorisation groups.
English – 11