Limited Warranty; Troubleshooting - KS RONDA N Manual De Instalación Y Funcionamiento

lImItED WARRANty

KASSEL SANITÄR S.L. warrants that its electronic products will be free of defects
in material and workmanship during normal use for two years from the date the
product is purchased.
If a defect is found in normal use, KASSEL SANITÄR S.L. will, at its discretion,
repair, provide a replacement part or product, or make appropriate adjustments.
Damage caused by accident, misuse, or abuse is not covered by this warranty.
Improper care and cleaning will void the warranty. Proof of purchase (original
sales receipt) must be provided to KASSEL SANITÄR S.L. with all warranty
claims.
KASSEL SANITÄR S.L. is not responsible for labor charges, installation, or other
incidental or consequential costs other than those noted above. In no event shall
the liability of KASSEL SANITÄR S.L. exceed the purchase price of the product.
If you believe that you have a warranty claim, contact your Kassel Distributor,
Dealer or Plumbing Contractor. Please be sure to provide all pertinent information
regarding your claim, including a complete description of the problem, the
product, model number, the date the product was purchased, from whom the
product was purchased and the installation date. Also include your original
invoice.
KASSEL SANITÄR S.L. AND/OR SELLER DISCLAIM ANY LIABILITY FOR SPECIAL,
INCIDENTAL OR CONSEQuENTIAL DAMAgES. This warranty excludes product
damage due to installation error, incorrect maintenance, wear and tear, battery,
product abuse, or product misuse, whether performed by a contractor, service
company, or the consumer. This warranty does not cover product damage caused
by the following:
- Incorrect installation.
- inversions of supply pipes.
- Pressures or temperatures exceeding recommended limits.
- Improper manipulation, tampering, bad or lapsed maintenance.
- Foreign bodies, dirt or scale introduced by the water supply or soap tank.
- use of the soap outside of viscosity specifications.
- Alteration of the original soap/foam dispenser components (including pipes).
18

tROuBlEShOOtING

PROBlEm INDIcAtOR cAuSE
No water 1.Sensor
coming flashes
out of the continuously
faucet: when user's Low battery.
hands are
within the
sensor's range.
2. LED in the
1. Range is too short.
sensor does
not flash once
2. Range is too long.
when user's
hands are
within the
3. Battery is completely used up
sensor's range.
4. unit is in "Security Mode"*
5. Sensor is picking up reflections from
the washbasin or another object.
3. LED in the
sensor flashes
once when
user's hands
1. Debris or scale in solenoid.
are within the
sensor's range.
2. The central orifice in the diaphragm is
plugged or the diaphragm is torn
3. The water supply pressure is higher
than 8 bar.
4. The water supply pressure is under 8
bars and yet the pressure in the faucet's
body is higher. This situation could be
caused by a sudden increase in the
water supply pressure that the backcheck
prevents from dropping, even after water
supply pressure drops under 8 bars.
Water flow 1. Sensor
1. Debris or scale in diaphragm
from spout flashes once
does not when user's
2. Connectors between the electronic
stop: hands are
unit and the Dual power input box are
within the
disconnected or not connected properly
sensor's range.
2. LED in the
1. Sensor is dirty or covered.**
sensor does
not flash once
when user's
2. Sensor is picking up reflections from
hands are
the washbasin or another object.
within the
sensor's range.
Water flow
Filter or aerator is clogged
diminished
* "Security Mode": If the sensor is covered for more than 90 sec. the faucet will automatically shut off
water flow.
To return to normal operation remove any blockage.
** In this case, the water flow will stop anyway after 90 seconds because of the security time.
SOlutION
Replace battery
Increase the range
Decrease the range
The battery must be
replaced.
Eliminate cause of reflection.
unscrew solenoid, pull out
the plunger and the spring
from the solenoid and clean
them. use scale remover
material if needed. When
replacing the plunger, please
make sure that the spring is
in vertical position.
Clean the orifice or replace
diaphragm.
Reduce the supply water
pressure.
Shut off water supply and
unscrew one of the flexible
pipes in order to reduce
the pressure that blocks the
product.
Clean the orifice or replace
diaphragm.
Connect the connectors
properly. Refer to pages
8/13/17 to see how.
Clean or eliminate case of
interference.
Decrease the range or
eliminate cause of reflection.
Remove, clean, re-install
19