Protecting The Environment - Stanley STDR5510 Manual De Instrucciones

a hammer as shown.
f Remove the Allen key.
f Remove the chuck by turning it counterclockwise.
f To refit the chuck, screw it onto the spindle and secure
it with the chuck retaining screw.
USE
Warning! Let the tool work at its own pace. Do not
overload.
¡Warning! Before drilling into walls, floors or ceilings,
check for the location of wiring and pipes.
Selecting the direction of rotation (Fig. D)
For drilling and for tightening screws, use forward
(clockwise) rotation. For loosening screws or removing a
jammed drill bit, use reverse (counterclockwise) rotation.
f To select forward rotation, push the forward/reverse
slider (3) to the centre position.
f To select reverse rotation, push the forward/reverse
slider to the left.
Viewed when holding the drill in the operating position.
After any reversing operations, return slider (3) to forward
position.
Warning! Never change the direction of rotation while
the motor is running.
Switching On and Off
f To switch the tool on, press the variable speed switch
(1). The tool speed depends on how far you press
the switch.
f For continuous operation, press the lock-on button
(2) and release the variable speed switch. This option
is available only at full speed.
f To switch the tool off, release the variable speed
switch. To switch the tool off when in continuous
operation, press the variable speed switch once more
and release it.
f Based on the different applications, turn around the
speed dial (9) to control the maximum speed.
Proper Hand Position (Fig.E)
Warning! To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown in Fig. E.
Warning! To reduce the risk of serious personal injury,
ALWAYS hold securely in anticipation of a sudden reaction.
Drilling in metal
Start drilling with slow speed and increase to full power
while applying firm pressure on the tool. A smooth even
flow of metal chips indicates the proper drilling rate. Use a
cutting lubricant when drilling metals. The exceptions are
cast iron and brass which should be drilled dry.
Note: Large [5/16" (8 mm) to 3/8" (10 mm)] holes in steel
can be made easier if a pilot hole [5/32"
(4 mm) to 3/16" (5 mm)] is drilled first.
Drilling in wood
Start drilling with slow speed and increase to full power
while applying firm pressure on the tool. Holes in wood
can be made with the same twist drills used for metal.
These bits may overheat unless pulled out frequently to
clear chips from the flutes. Work that is apt to splinter
should be backed up with a block of wood.
MAINTENANCE
Your tool has been designed operate over a long period of
time with minimum of maintenance. Continuous satisfactory
operation depends proper tool care and regular cleaning.
¡Warning! Before performing any maintenance, switch
off and unplug the tool.
f Regularly clean the ventilation slots in your tool using
a soft brush or dry cloth.
f Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
REMARKS
f STANLEY policy is one of continuous improvement to
our products and as such, we reserve the right to modify
f Standard equipment and accessories may vary by country.
f Complete product range may not be available in all
countries.
f Contact your local STANLEY dealers for range availability.
ACCESSORIES
The performance of your tool depends on the accessory used.
STANLEY accessories are engineered to high quality standards
and designed to enhance the performance of your tool. By using
these accessories you will get the very best from your tool.

PROTECTING THE ENVIRONMENT

Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your STANLEY
product needs replacement, or if it is of no further
use to you, do not dispose of it with household waste.
Make this product available for separate collection.
Separate collection of used products and packaging
allows materials to be recycled and used again.
Re-use of recycled materials helps prevent
environmental pollution and reduces the demand
for raw materials. Local regulations may provide for
separate collection of electrical products from the
household, at municipal waste sites or by the
retailer when you purchase a new product.
ENGLISH • 13