Denon AVC-A11SR Instrucciones De Operación página 14

ENGLISH
Setting the channel level
• Use this setting to adjust so that the playback level between the different channels is equal.
• From the listening position, listen to the test tones produced from the speakers to adjust the level.
• The level can also be adjusted directly from the remote control unit. (For details, see page 27.)
• When using both surround speakers A and B, their playback levels can be adjusted separately.
1
At the System Setup Menu select "Channel Level".
TUNING
BAND MODE
TUNING
2
Switch to the Channel Level screen.
ENTER / SH FT
SELEC
3
Select "Test Tone Mode".
TUNING
BAND MODE
TUNING
4
Select the mode.
TUNING
Select "Auto" or "Manual".
• Auto:
BAND M
Adjust the level while listening to the test tones produced
TUNING
automatically from the different speakers.
• Manual:
Select the speaker from which you want to produce the
test tone to adjust the level.
5
Select "Surr. Sp.", then select the surround speaker(s) from which you
UNING
TUNING want to produce the test tone (A, B or A+B).
• Surr. Sp.: A
BAND MODE
BAND M
TUNING
TUNING
• Surr. Sp.: B
• Surr. Sp.: A+B
6
Select "Test Tone Start".
TUNING
BAND MODE
TUNING
14
Example: When the "Auto" mode is selected
Adjusts the balance of the playback level between the channels when
using surround speaker A.
Adjusts the balance of the playback level between the channels when
using surround speaker B.
Adjusts the balance of the playback level between the channels when
using surround speakers A and B at the same time.
The "Surr. Sp." can only be selected when both surround speakers
A and B have been selected at the "Speaker Configuration" (when
both A and B have been set to "Large" or "Small").
7
Select "Yes".
UN NG
BAN MODE
8
a. If the "Auto" mode is selected:
Test tones are automatically emitted from the different
speakers.
The test tones are emitted from the different speakers in
the following order, at 4-second intervals the first time and
second time around, 2-second intervals the third time
around and on:
FL C FR SR
When the surround back speaker setting is set to
"1spkr" for "Speaker Configuration", this is set to "SB".
Use the CURSOR buttons to adjust all the speakers to the
UNING
same volume.
BAND MODE
The volume can be adjusted between –12 dB and +12 dB in
TUNING
units of 1 dB.
b. When the "Manual" mode is selected:
TUN NG
Use the CURSOR left and right to select the speaker for
which you want to output test tones, then use the
BAND M E
CURSOR up and down to adjust so that the volume of the
TUN NG
test tones from the various speakers is the same.
UNING
BAND MODE
TUNING
9
After the above settings are completed, press the ENTER button again.
ENTER / SHIFT
The "Channel Level" screen reappears.
SELEC
To cancel the settings, select "Level Clear" and "Yes" on the "Channel Level" screen, then make the
settings again.
The level of each channel should be adjusted to 75 dB (C-weighted, slow meter mode) on a sound level meter
at the listening position.
If a sound level meter is not available adjust the channels by ear so the sound levels are the same. Because
adjusting the subwoofer level test tone by ear is difficult, use a well known music selection and adjust for natural
balance.
NOTE: When adjusting the level of an active subwoofer system, you may also need to adjust the subwoofer's
own volume control.
Flashing
1spkr
Example: When the volume is set to
SB
–12 dB while the test tone
SBR SBL SL SW
is being produced from the
2spkrs subwoofer
Flashing
Example: When the volume is set to
–12 dB while the
subwoofer is selected