Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Lever Handle Installation
4.5
Attach the plastic
handle adapter (I)
to the cartridge
D
stem using the 1/2
inch adapter screw
(J). Make sure the
ridges on the back
I
of the adapter (I) are
J
to the left of the tab
on limit stop (D).
5.
Setting The Temperature Limit Stop and Finishing Your
Tub/Shower Installation
5.1
5.2
HOTTEST
120F
(49C)
Turn on the hot and cold
water supply to check for
If temperature exceeds 120 degrees, go to step 5.3.
leaks and set temperature
If temperature is less than 120 degrees, go to step 5.5.
limit stop.
5.3
5.4
1
D
1
K
I
J
2
3
+
D
-
D
Remove the lever (K) and
After setting the adjustable
lever handle adapter (I).
temperature limit stop (D) to
Note the position of the
the desired position, reattach
stop. Position the adjustable
the lever handle adapter (I),
temperature limit stop (D) so
adapter screw (J), and lever
the lever stops at that posi-
(K) – make sure ridges on back
tion. This prevents the lever
of (I) are to the left of the tab
from being turned into an
on (D).
unsafe temperature.
Place the lever (K)
on the lever handle
adapter.
K
Rotate the lever counterclockwise until
the water is to the maximum desired
temperature, not to exceed 120 degrees F
(49 degrees C). Seasonal maintenance of
the maximum outlet temperature may be
required due to changes in groundwater
temperature.
TURN LEVER TO THE OFF POSITION
ONCE THE TEMPERATURE IS SET.
5.5
D
I
K
J
J
Using 7/64 inches hex
wrench (M), insert and
tighten adapter screw (J)
into lever (K).
E10
Care Instructions
To preserve the finish on the metallic parts of your Moen faucet, apply non-abrasive wax, such
as car wax. Any cleaners should be rinsed off immediately.
To preserve the finish on the metallic parts of your Moen faucet, apply non-abrasive wax, such
as car wax. Any cleaners should be rinsed off immediately.
Spot Resist™ Stainless and Spot Resist™ Brushed Nickel Finishes:
Moen recommends cleaning the Spot Resist finish with a mild soap, rinsing thoroughly
with warm water and drying with a clean, soft cloth. Never use cleaners containing abrasives
(including abrasive sponges or steel wool), ammonia, bleach or sodium hypochlorite, organic
solvents (e.g. alcohols) or other harsh chemicals (e.g. lime scale removers) to clean the Spot
Resist finish, as they may damage the finish. Failure to comply with these cleaning instructions
may void Moen's warranty.
Moen products have been manufactured under the highest standards of quality and workmanship.
Moen warrants to the original consumer purchaser for as long as the original consumer purchaser
owns their home (the "Warranty Period" for homeowners), that this faucet will be leak- and drip-free
during normal use and all parts and finishes of this faucet will be free from defects in material and
manufacturing workmanship. All other purchasers (including purchasers for industrial, commercial and
business use) are warranted for a period of 5 years from the original date of purchase (the "Warranty
Period" for non-homeowners).
If this faucet should ever develop a leak or drip during the Warranty Period, Moen will FREE OF
CHARGE provide the parts necessary to put the faucet back in good working condition and will
replace FREE OF CHARGE any part or finish that proves defective in material and manufacturing
workmanship, under normal installation, use and service. Replacement parts may be obtained
by calling 1-800-289-6636 (Canada 1-800-465-6130), or by writing to the address shown. Proof of
purchase (original sales receipt) from the original consumer purchaser must accompany all warranty
claims. Defects or damage caused by the use of other than genuine Moen parts is not covered by this
warranty. This warranty is applicable only to faucets purchased after December, 1995 and shall be
effective from the date of purchase as shown on purchaser's receipt.
This warranty is extensive in that it covers replacement of all defective parts and finishes. However,
damage due to installation error, product abuse, product misuse, or use of cleaners containing
abrasives, alcohol or other organic solvents, whether performed by a contractor, service company,
or yourself, are excluded from this warranty. Moen will not be responsible for labor charges and/or
damage incurred in installation, repair or replacement, nor for any indirect, incidental or consequential
damages, losses, injury or costs of any nature relating to this faucet. Except as provided by law, this
warranty is in lieu of and excludes all other warranties, conditions and guarantees, whether expressed
or implied, statutory or otherwise, including without restriction those of merchantability or of fitness
for use.
Some states, provinces and nations do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights and you may also have other rights which vary from state to state,
K
province to province, nation to nation. Moen will advise you of the procedure to follow in making
warranty claims. Simply write to Moen Incorporated using the address below. Explain the defect and
include proof of purchase and your name, address, area code and telephone number.
M
Shower heads: Standard 9.5 L/min (2.5 gpm) max. and High Efficiency 7.6 L/min (2.0 gpm)
max. or less
For use with automatic compensating valves rated at 5.7 L/min (1.5 gpm) or less
Automatic Compensating Valves:
Posi-Temp® and CFG®: For use with Showerheads rated at 5.7 L/min (1.5 gpm) or higher
ExactTemp® and ioDigital™: For use with Showerheads rated at 9.5 L/min (2.5 gpm) or higher
Moentrol®: For use with Showerheads rated at 4.9 L/min (1.3 gpm) or higher
Cleaning Instructions
Moen Lifetime Limited Warranty
Moen Incorporated
25300 Al Moen Drive, North Olmsted, Ohio 44070-8022 U.S.A.
E11
Publicidad
Capítulos
Tabla de contenido
