Install The Door Control - Craftsman 139.53925DS Manual Del Propietário

mNSTALLATION STEP 7
Install the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet (1.52 m) where small children cannot
reach, away from moving parts of door and door
hardware., if installing into drywall, drill 5/32" holes and use
the anchors provided.. For pre-wired installations (as in
new home construction), it may be mounted to a single
gang box (Figure 2)..
1_Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red wire
to the 1.
2..Remove cover by gently prying at slot in side of the
cover with a small flat head screwdriver.. Fasten with
6ABx1-1/4" self-tapping screws (drywall installation) or
6-32xl" machine screws (into gang box) as follows:
• Drill and install bottom screw, allowing 1/8" (3 mm) to
protrude above wall surface_
- Position bottom of door control on screw head and
slide down to secure.. Adjust screw for snug fit.
° Drill and install top screw with care to avoid cracking
plastic housing,. Do not over tighten.
• Insert top tabs and snap on cover..
3. (Standard installation only) Run bell wire up walt and
across ceiling to motor unit,.Use insulated staples to
secure wire in several places° Do not pierce wire with a
staple, creating a short or open circuit.. If your access
door is near the garage door, you may run this wire with
the Safety Reversing Sensor wires along the top of the
rail.. See page 17,.
4.. Insert a!l wires through the opening on top of motor unit
above the terminal block on the back panel (Figure 3).
5o Strip 7/16" (11 mm) of insulation from each set of wires..
Insert door control wire into quick-connect terminals by
color: white wire to white, white/red wire to red.
Separate white and white/black wires sufficiently to
connect to the opener quick-connect terminals. Twist
like colored wires together_ Insert wires into
quick-connect holes: white to white and white/black to
grey,
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires into
quick-connect holes: white to white and red/white to red.
6.,Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE: DO NOT connect the power and operate the
opener at this time. The trolley will travel to the full open
position but will not return to the close position until the Door c ontrol
sensor beam is connected and properly aligned.
Connections
To prevent possibleSERIOUSINJURYor DEATH from
electrocution:
• Be sure power is not connectedBEFORE installing door
control.
• ConnectONLYto 24 VOLTlow voltagewires..
To prevent possibleSERIOUS INJURYor DEATH from a closing
garagedoor:
• Install door control within sight of garagedoor, out of reach
of childrenat a minimum height of 5' (1..5m), and away from
all moving parts of door.
• NEVER permit childrento operateor playwith door control
push buttons or remote control transmitters,
° Activatedoor ONLYwhen it can be seenclearly,is properly
adjusted,andthere are no obstructionsto door travel
• ALWAYSkeepgaragedoor in sight until completelydosed
NEVER permit anyoneto cross path of closing garagedoor_
Outside Keylock Accessory' Connections
To opener quick-connect terminals: white to white; white/
red to red..
HARDWARE SHOWN ACTUAL SIZE
Control Panel(std Installation)
Control Panel (pro-wired)
_ nsulated
SlapIes
Drywall Anchors
CONTROL
CONSOLE -_ Top
Mounting Hole
Ughled >. Terminat
Push Screws
Button - Bottom
Mounting Hole
BACK ViEW
Figure I Figure 2
REMOVE & REPLACE COVER PRE-WIRED
INSTALLATION
To Replace,
Insert Top
Tabs First ,,"
Twist
Here
Figure 3
Strip 7/16" (11 mm) or' insulation from each wire
Insert wires through opening on top of motor
unlt above termina! block, then into
quick.connect terminals
To release or insert wire,
=ush tn tab wilh screwdriver
24 Volt
2-Conductor
Bell Wire
Slrip wire 7116" (t t ram)
;led White Grey
2O