Using Your Cooking Food Processor; Standby Mode; After Cooking - Kenwood CCL45 Instrucciones

using your cooking food
processor
1 Plug in and press the On/Off switch
right side of the power unit. The unit will beep and
"WELCOME TO kCook" will be displayed.
2 Fit the bowl
bn
locating tab to the back of the unit. Press down
lightly to locate. Note: the bowl cannot be located
unless fitted in the correct orientation.
To remove the bowl, push both bowl release
l
buttons (situated under the bowl handles) at the
bo
same time and lift the bowl.
3 Select one of the following options:
3A Manual Cooking – refer to manual mode
section.
3B Pre-set Programmes:
Refer to 'using the pre-set programmes' section for
usage information.
Main Meal programme
Sauce programme
Steam programme
Soup programme
temp time speed servings
Stir Fry programme
time speed servings
Dessert programme
time speed servings
Note: When a pre-set programme button is pressed
speed servings
the bar above the relevant button will light up.
servings
4 Fit the maxblade
whisk tool
9
bowl.
Bowl tool
temp time speed
maxblade
temp time speed
speed
Knife blade
Stir tool
Whisk tool
5 Add the relevant ingredients to be processed or
cooked.
ck
to the power unit by aligning the
c
cr
cs
ct
dk
dl
a, knife blade b, stir tool
7 7
or slow cook bowl plug
Use
For chopping ingredients
before cooking and for
pureeing after cooking is
complete.
For making doughs and cake
batters.
For recipes where you want to
stir gently without breaking the
ingredients down.
For whisking light ingredients
such as egg whites, cream,
mayonnaise and hollandaise
sauce.
6 Fit the lid and filler cap. Push the lid down and turn
anti-clockwise until aligned with the cooking bowl
handles.
The appliance will not operate unless
on the
interlocked correctly.
7 Press the cooking bowl Start/Stop button
start the cooking process.
8 Pre-set programmes – at the end of each stage and
once cooking has finished the unit will beep and
automatically go into the Keep Warm cycle for 30
minutes. Follow the instructions on the screen to
move to the next stage.
9 To stop the unit at any time, press the Start/Stop
button and then remove the lid. Take care as the
bowl and lid will be hot. To resume cooking, refit
the lid press the Start/Stop button.
Manual
l
countdown to 00:00 and the unit will beep.

Standby Mode

To return the unit to standby mode, press and hold
l
the Cancel button for 3 seconds.
If no selection is made within 30 minutes the unit
l
will go into standby mode and "WELCOME TO
kCook" will be displayed on the screen. Press any
function to reactivate the unit.
Keep Warm Cycle
The Keep Warm cycle will stir the ingredients at
l
62°C.
Remove the lid to check on the progress or add
l
other ingredients and then press the Start/Stop
button to resume cooking.
,
8
When the timer has counted down to 00:00 at
l
to the
l
the end of each programme stage the unit will
automatically go into the keep warm cycle for 30
minutes.
The unit will beep every 10 seconds for the first
l
minute and then every 30 seconds to indicate the
unit is in the Keep Warm cycle and the cooking
cycle has finished.
The keep warm cycle will not heat if the
l
temperature is set to less than 62˚C.

After cooking

Be careful when handling or touching any part
l
of the appliance when being used in the cooking
mode or after cooking, IN PARTICULAR THE
BOWL AND TOOLS as they will remain HOT long
after the appliance has been switched off.
Use the handles to remove and carry the bowl. Use
l
oven gloves when handling the hot bowl and hot
tools.
The underside of the bowl will remain hot long
l
after the heating has stopped. Use caution when
handling and cleaning.
9
mode – at the end of cooking the timer will
to
k