Product Familiarisation - Silverline 103597 Traducción Del Manual Original

Soldador de arco inverter 200 a, mma

Ocultar thumbs Ver también para 103597:

Manual de instrucciones (41 páginas)

Contenido

Tabla de contenido

Idiomas disponibles

103597

12 Secure work - Where possible use clamps or a vice to hold the work . It is safer than using your

hands

13 Do not overreach - Keep proper footing and balance at all times

14 Maintain tools with care

Keeping cutting tools sharp and clean makes the tool easier to control and less likely to bind or

lock in the workpiece

Follow instructions for lubricating and changing accessories

Inspect tool power cables periodically and have them repaired by an authorised service facility if

damaged

Inspect extension cables periodically and replace if damaged

Keep handles dry, clean and free from oil and grease

WARNING: Many accidents are caused by poorly maintained power tools .

15 Disconnect tools - Disconnect tools from the power supply when not in use, before servicing and

when changing accessories such as blades, bits and cutters

WARNING: The use of accessories or attachments not recommended by the manufacturer may

result in a risk of injury to persons.

16 Remove adjusting keys and wrenches - Form the habit of checking to see that keys and

adjusting wrenches are removed from the tool before switching it on

17 Avoid unintentional starting - Ensure switch is in "off" position when connecting to a mains

socket, inserting a battery pack, or when picking up or carrying the tool

WARNING: Unintended starting of a tool can cause major injuries.

18 Use outdoor extension leads - When the tool is used outdoors, use only extension cords

intended for outdoor use and so marked . Use of an extension cable suitable for outdoor use

reduces the risk of electric shock

19 Stay alert

Watch what you are doing, use common sense and do not operate the tool when you are tired

Do not use a power tool while you are under the influence of drugs, alcohol or medication

WARNING: A moment of inattention while operating power tools may result in serious personal

injury.

20 Check damaged parts

Before further use of tool, it should be carefully checked to determine that it will operate properly

and perform its intended function

Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and

any other conditions that may affect its operation

A guard or other part that is damaged should be properly repaired or replaced by an authorised

service centre unless otherwise indicated in this instruction manual

Have defective switches replaced by an authorised service centre

WARNING: Do not use the tool if the on/off switch does not switch the tool on and off . The switch

must be repaired before the tool is used .

21 Have your tool repaired by a qualified person - This electric tool complies with the relevant

safety rules. Repairs should only be carried out by qualified persons, otherwise this may result in

considerable danger to the user

WARNING: When servicing use only identical replacement parts .

WARNING: If the power cable is damaged it must be replaced by the manufacturer or an

authorised service centre .

22 Power tool mains plugs must match the mains socket - Never modify the plug in any way .

Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching sockets will reduce risk of electric shock

23 If operating a power tool outside use a residual current device (RCD) - Use of an RCD

reduces the risk of electric shock

NOTE: The term "residual current device (RCD)" may be replaced by the term "ground fault circuit

interrupter (GFCI)" or "earth leakage circuit breaker (ELCB)" .

WARNING: When used in Australia or New Zealand, it is recommended that this tool is ALWAYS

supplied via Residual Current Device (RCD) with a rated residual current of 30mA or less .

WARNING: Before connecting a tool to a power source (mains switch power point receptacle, outlet,

etc.) be sure that the voltage supply is the same as that specified on the nameplate of the tool. A

power source with a voltage greater than that specified for the tool can result in serious injury to

the user, and damage to the tool . If in doubt, do not plug in the tool . Using a power source with a

voltage less than the nameplate rating is harmful to the motor .

Welding Safety

• Welding produces toxic fumes and can reduce oxygen levels in the work area . Always work in a

well-ventilated area . Avoid inhaling welding fumes, use a suitable respirator where appropriate

• Some metal parts may have zinc, lead, cadmium or other coatings . Attempting to weld through

these coatings can produce highly toxic fumes . Always remove all coatings before welding

• If you experience irritation to the lungs, throat or eyes whilst welding, STOP IMMEDIATELY and

seek fresh air

• Welding produces extremely high levels of UV light . To prevent eye damage, ALWAYS use an

approved welding face mask . Under no circumstances look directly at the arc

• The light produced when arc welding can be attractive to look at, especially to children . Always

prevent other people from viewing the arc welding light with unprotected eyes

200A MMA Inverter Arc Welder Kit

• If there is a possibility of other people approaching the work area, erect suitable screening to

protect them from the light / glare

• Always replace the welder face mask glass as soon as it shows any signs of wear or damage

• To prevent skin damage, ALWAYS wear a suitable fire-proof long sleeved jacket, heat proof gloves,

and cap . Keep covered up

• Always remove any flammable materials (e.g. cigarette lighter, matches) from your clothing

before welding

• Always keep a fire extinguisher nearby when welding

• Sparks generated while welding can ignite flammable materials easily in the welding area, so it

is important to remove flammable materials before commencing welding

• Only weld when the work area and all workpieces are dry

• Do not weld sealed containers (e .g . fuel tanks, air tanks, oil drums) . The heat generated from

welding can cause sealed containers to burst without warning

• Be aware of transferred heat . Metal parts can conduct heat away from the work area and cause

ignition of flammable materials

• Be aware that welded parts will remain hot for some time after joining. Allow to cool completely

before handling, or leaving unattended

• Never weld where flammable gases, liquids or dust are present

• Ensure that there is always a responsible person nearby to alert you to any fire, or to call help

in an emergency

• Use of welding machines will create powerful magnetic fields. This may disturb the operation

of sensitive electronic equipment. Pacemaker wearers should consult a doctor before using a

welding machine

• Do not overload power supply. Check that your mains wiring is capable of delivering the required

current safely (see Specification)