Service Parts; Service Notes - Broan SPK110 Manual De Instrucciones

INSTALL GRILLE
6. Finish ceiling.
Install ceiling material. Cut out around housing.
7. Attach grille
to housing.
Squeeze grille
springs and insert
them into slots on
each side of hous-
ing.
8. Push grille
against
ceiling.

SERVICE NOTES

To remove Blower Assembly:
Remove speaker assembly (see below). Unplug motor. Remove thumbscrew (10) from motor
plate flange Find the single TAB on the motor plate (located next to the receptacle). Push up
near motor plate tab while pushing out on side of housing. Or insert a straight-blade screwdriver
into slot in housing (next to tab) and twist screwdriver.
To remove Speaker Assembly:
Unplug motor from speaker wiring. Unplug speaker wiring from wire panel. Remove (2) screws
from speaker bracket. Unhook speaker bracket from motor bracket and remove speaker.
The Bluetooth word mark and logos are registered trademarks owned by Bluetooth
®
such marks by Broan-NuTone LLC is under license. Other trademark and trade names are those of their respective
owners.
WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate this equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation. FCC ID: 2ADLL-99528551
This Bluetooth wireless technology enabled Speaker complies with FCC radiation exposure limits set forth for
®
an uncontrolled environment. End users must follow the specific operating instructions for satisfying exposure
compliance. This speaker must not be co-located or operate in conjunction with any other antenna or transmitter.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate this equipment.
NOTE: The Grantee is not responsible for any changes or modifications not expressly approved by the party
responsible for compliance. Such modifications could void the user's authority to operate the equipment.

SERVICE PARTS

Key No. Part No.
1 97016466
2 97016449
3 98010102
4 99170245
5 97018010
6 97018218
7 97016497
8 99140199
9 97018014
10 99420665
11 SPKACC
12 99160459
Order service parts by "Part No." - not by "Key No."
Replacement parts can be ordered on our website.
Please visit us at www.broan.com
2
SIG, Inc. and any use of
®
MODEL SPK110
Description
Housing
Duct Connector-4"
Wiring Plate
Screw, #8-18 X .375
Wire Panel/Harness Assembly
Blower Assembly
Grille Assembly
(includes key no. 8)
Grille Spring (2 req'd)
Spacer (2 supplied)
Thumbscrew, #8-18 x .375
Speaker
Screw, #8-32 x .625 Hex Head (2 req'd)
9
1
5
LENGÜETA
10
12
Page 4
9
3
4
11
99045246A