Safety Warnings - Senco Smart BoardMaster Instrucciones De Empleo

SAFETY WARNINGS

EN
y Read and understand these warn-
ings to prevent injuries to yourself
and bystanders. Refer to tool use,
maintenance and troubleshooting
sections for additional information.
y
Failure to follow warnings could result in serious injury.
y
Do not discard.
y Operators and others in work area shall wear
impact-resistant eye protection with side
shields. Failure to do so can cause serious
injury. CE equivalent to EN166
y Always wear other personal protective
equipment such as hearing, gloves and
hard hat.
y Only wear gloves that provide adequate
feel and safe control of triggers and
adjusting devises.
y
Operators and others in work area shall wear hearing
protection.
y Unprotected exposure to high noise levels can cause
permanent, disabling, hearing loss and other problems
such as tinnitus (ringing, buzzing, whistling or humming
in the ears).
y Appropriate controls to reduce the risk may include
actions such as damping materials to prevent workpieces
from "ringing".
y
Use appropriate hearing protection.
y Operate and maintain the tool as recommended in these
instructions, to prevent an unnecessary increase in noise
levels.
y If the tool has a silencer, always ensure it is in place and
in good working order when the tool is being operated.
y Exposure to vibration can cause disabling dam-
age to the nerves and blood supply of the hands
and arms.
y
Wear warm clothing when working in cold
conditions, keep your hands warm and dry.
y
If you experience numbness, tingling, pain
or whitening of the skin in your fingers or hands, seek
medical advice from a qualified occupational health
professional regarding overall activities.
y Operate and maintain the tool as recommended in these
instructions, to prevent an unnecessary increase in
vibration levels.
y
Hold the tool with a light, but safe, grip because the risk
from vibration is generally greater when the grip force
is higher.
y Stay alert, watch what you are doing, and use common
sense when operating a power tool. Do not use tool while
tired or under the influence of drugs, alcohol, or medica-
tion. A moment of inattention while operating power
tools may result in serious personal injury.
y
Only use correct energy supply as
directed
y Never use oxygen, carbon dioxide or any
other bottled gas as a power source for
this tool; the tool will explode and cause
serious injury.
y Using oxygen or combustible gases for pneumatic tools
creates a fire or explosion hazard.
y Always remove finger from trigger when
not driving fasteners. Never carry the
tool with finger on or under trigger. Tool
will eject a fastener if the workpiece
contact is bumped.
y Tool's resting position is on its side
disconnected from air.
y Resting position includes removing finger from trigger
and positioning tool so that the workpiece contact is not
actuated.
y Always assume the tool contains fasteners. Keep the tool
pointed away from yourself and others. No horseplay.
Respect the tool as a working implement.
y Keep hands and legs away from firing direction.
y Only skilled operators should use fastener driving tools.
y Drive fasteners into work surface
only; never into materials too
hard to penetrate.
y
Addition downforce is required for
steel and concrete tools.
y
During operation, debris from
from workpiece & collation system may be discharged.
y Ensure tool is always safely engaged on the workpiece
and cannot slip.
y Tools equipped with "Contact Actuation" shall
not be used:
If a change of driving locations is effected
‡
via stairs, ladders or scaffolding.
For closing boxes or crates.
‡
For fitting transportation safety systems.
‡
Moving platforms
‡
y
Read and understand risk associated with selective
actuation in "Tool Use" Section.
y Do not force tool. Let the tool do the work. Use the cor-
rect tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
y
Do not overeach
y
Keep proper footing and balance at all times.
y
Do not drive fasteners on top of
other fasteners or with the tool at
too steep of an angle.
y Fastener could deflect and cause
injury.
4