Base Setting - FREEWIRE FW295 Manual Del Usuario

enter the new PIN, press left soft key, enter again the new PIN, press OK.
"Reset Handset": to reset the handset, To reset the handset: press OK; enter the handset pin (0000
default setting) then press OK, is possible to select between 3 different kind of reset: "Phone Book":
to delete the whole phone book; "Settings": to reset settings at the default settings (also the
Appointment); "Handset": reset Phone book and settings; then press 2 times OK to confirm.
Babymonitor
if you have at least 2 handset subscribed on the same base (see "Multi handset configuration") is
possible active the BabyMonitor on a handset. When BabyMonitor is enabled, the handset with
babymonitor active when there is a noise/voice/cry on the place where is left, it calls automatically the
other handset selected or the external number set. Enter on handset setting then select
"Babymonitor" and press left soft key, select "Int Call" to make the Babymonitor call toward to an
handset subscribed on the same base, select "Ext Call" to make the Babymonitor call toward to an
external telephone number, or choose "Level" to select the sensibility level to start the call; then press
OK soft key. If you select "Int Call" enter the number of handset to call, if you select "Ext Call" enter
the external telephone number to call; then press OK to confirm. If is active on stand-by is displayed
the writing "Baby Monitor". When handset hear a noise/voice/crywill call the other handset selected or
the external number set then:-if the BabyMonitor is on internal call, is sufficient to close the line on
the parent handset; -if the Babymonitor is on external call, after 2 minutes of conversation the
babymonitor handset will close the line. If after that there are noise/voice/crying it will recall the
external number. To disable the Babymonitor press the soft key "End" on the Babymonitor handset
when is on-hook. WARNING: the handset with BabyMonitor activated doesn't ring at the external call.
Emergency Call (care dial)
With this procedure is possible to saved 3 telephone number to recall in case of emergency by a long
press on key. To set the number press "Menu" soft key, select "HS Setting" then press OK; select
"Care Dial" option, press OK; "Care Dial 1" is displayed, press OK soft key then enter the first number
of the list, then press OK soft key. Use keys to set the 2nd care dial number ("Care Dial 2") and
the 3rd care dial number ("Care Dial 3"). To start an emergency call, with the handset on on-hook,
keep pressing key, the handset will switch on hands free and start to call the first emergency
number. If the other party answer the handset remain on conversation for 2 minutes, after that
disengage the line and call the second emergency number ad so on. If an emergency number is
busy, it pass directly to call the next number. After 3 times that handset calls the emergency number it
will end automatically the Emergency call or press key to end the emergency call.

BASE SETTING

To change the base setting press left soft key "Menu", press 4 times , "Base Setting" is displayed.
Press left soft key, wait a moment, now is possible to change the following setting:
"PABX code": to automatically add the PABX exit code (1 digit usually 0 or 9) before the phone
number save on Phone Book and before to the numbers recall from Missed/Received calls list.
Moreover each time you type a number that have as initial digit the PABX exit code, FW295 add
automatically a pause between PABX code and phone number to make easier the link between
PABX and public line. Press OK; enter the PABX code and press OK to confirm.
"Ring Melody": to select the melody of the ring tone of the base, press OK, use to select the tone
select "0" to disable the base ring. Press OK keys to confirm.
"Ring Volume": to select the desired volume of the base ring volume, press OK, use keys to choose
the volume then press left soft key to confirm.
"Desub HS": to de-register an handset from the base, press OK, enter the base pin code (0000
default) then press OK; select the handset number to desuscribe then press OK to confirm (is not
possible to desuscribe the handset that make the procedure).
"Change PIN": to change the PIN of the base, enter the previous pin (0000 default setting) then
press OK. Enter the desired new pin then press OK; enter again the new PIN then press OK to
confirm the modify.
"Call Barring": it's possible to lock until 5 area codes (max. 5 digits each one). For each area code is
possible to choose which handset have to be locked. Press OK, enter the pin of the base (0000
default setting) then press OK, enter the first area code to lock or pass at the following or precedent
area code to lock by keys then press OK to confirm; use the numeric keypad to choose which
handsets have to be locked, for example press 1 to lock the handset 1, press again to unlock, the
EN