Publicidad
Idiomas disponibles
Idiomas disponibles
If during an intercommunication between handset you receive an incoming call, the base ring on
handsets the EXT icon is blinking. To answer: end the internal call by
key; wait that handset ring
then press
key to answer the call.
Call transfer between handset
During external conversation keep pressing INT key; press the number key that correspond at the
handset number to call (example press 1 key to call Handset 1); when the other handset answer, an
internal call start; to transfer the call press
key on your handset, to not transfer the call press
again INT key.
Conference Call
An external conversation can be shared at 2 handset so you have a conference between 3 person.
At the point 4 of previous procedure ("Call transfer between handset") press "Conf" soft key on the
handset that start the internal conversation. To end the conference press "End CF".
Multi base configuration
Thanks to the GAP profile is possible subscribe your handset at 4 different base station (also of
different and/or brand), is sufficient that are DECT with GAP profile.
that allows to create a wide coverage area, note that the base station doesn't amplify the signal that
means that the other base aren't signal repeater but they working as cell so each base need the
telephone line and the handset when lost the signal will link at another base and not at the original
base through the other base. The intercommunication between handset working only if the 2 handset
are linking at the same base station.
Subscription of handset to another base
The procedure to be follow is the same of "Handset subscription", the difference are:
Handset and Base of FW295: follow "Handset subscription" procedure except that at 3 point you
need to choose a progressive number of base. If base is different from FW295:Follow the procedure
of other model to put the base on "Subscription mode" (usually keep pressing PAGE key), then follow
the procedure "Handset subscription" from point 2 to the end of procedure, at point 5 type the base
pin code of the other model.
If handset is different from FW295:Put the FW295 base on "Subscription mode" (follow point 1 of
"Handset subscription") and follow the subscription procedure of the handset of the other model
(remember to use PIN code of FW295 base, 0000 default).
Base selection
Press "Menu" soft key and select "HS Setting" then press "OK"; select "Select Base" option then
press OK; use
keys to select the base that you want to link then press OK (select "Ӿ" for a
automatic choose); wait some seconds, "Base: X" (where X is the base number that you choose at
the previously point); press OK to confirm or "Back" to not change the link base station
NOTE: If after 5-10 seconds the handset doesn't found your desired base but at 6 point remain "New
Base X" (where X is the desired base number) it means that the handset doesn't found the base;
approach the desired base or press
key and repeat the procedure but choose another base.
WARNING: when you pass from a base to another base if you are making a conversation probably it
will be lost.The automatic search will be activate until you make a new subscription with that handset
or until you make a manual searching of the base.
Icon of new message on centralized answer service
If your Network provider provide a centralized answer service that means not an answering machine
on your house but an answering service managed by phone line, FW295 will signal by
icon
when there are new message on centralized answer service. After that you listen the new message,
the Network provider will send a message to your cordless and the icon switch off.
NOTE: this features may be not available on your country.
FAQ - Troubleshooting
I don't listen the line tone -When you press
key the green led on base switch on? NO: follow
"Handset Subscription" procedure YES: Try to use only FW295 on your telephone line, if alone
working, try to exchange the position of the telephone.
Handset doesn't ring - Solution: Handset Reset at Settings level or try to deactivate Babysit or check
that handset external ring melody is not on "0";
Lost of audio during conversation or beep during conversation - Approach to the base station or try to
position the base on a central position or also displace the base of 20-30cm. from the previously
EN
Publicidad
