Tabla de contenido
Publicidad
SAFETY INSTRUCTIONS
© Stanley Bostitch
IMPORTANT READ CAREFULLY: It is important that all operators read and understand all sections
of this Tool Technical Data manual and the separate Safety and Operating Instruction Manual which come with
GB Not to be reproduced without permission. Unauthorised copies of this document do not constitute CE
this tool. Failure to do so could result in you or others in the working area to be seriously injured.
compliance for the products.
WARNING! Eye protection in accordance with 89/686/EEC, and with equal or greater grade than defined in
FR Reproduction interdite sans permission préalable. Les copies non autorisées de ce document ne signifient en
EN166 should be used. However all aspects of operators work, environment and other type/s of machinery
rien que les produits soient conformes aux normes CE.
being used, should also be considered when selecting any personal protection equipment. Note: Non-side
shielded spectacles and face shields alone do not provide adequate protection.
DE Vervielfältigung nicht ohne Genehmigung gestattet. Unzulässig erstellte Kopien dieses Dokuments erfüllen nicht
die CE-Richtlinien für Produkte.
WARNING! To prevent accidental injuries:
•
Never place a hand or any other part of the body in fastener discharge area of tool.
NL Mag niet worden vermenigvuldigd zonder toestemming. Onrechtmatige kopieën van dit document willen niet
•
Never point tool at yourself or anyone whether it contains fasteners or not.
zeggen dat de producten voldoen aan de CE-vereisten.
•
Never engage in horseplay.
•
Never pull the trigger unless the nose is directed towards the work.
DK Må ikke gengives uden tilladelse. Uautoriserede kopier af dette dokument udgør ikke CE overholdelse for
•
Always handle the tool with care.
produkterne.
•
Do not pull the trigger or depress the trip mechanism whilst loading the tool.
•
To prevent accidental actuation and possible injury, always disconnect air supply.
FI Ei saa jäljentää ilman lupaa. Tämän asiakirjan ilman valtuutusta tehdyt kopiot eivät muodosta tuotteille CE-
1. Before making adjustments. 2. When servicing the tool. 3. When clearing a jam. 4. When tool is not in use.
yhdenmukaisuutta.
5. When moving to a different work area, as accidental actuation may occur, possibly causing injury.
•
Read the additional Safety & Operating instructions booklet before using tool.
GR Απαγορεύεται η αναπαραγωγή χωρίς προηγούμενη άδεια. Τα μη εξουσιοδοτημένα αντίγραφα του παρόντος
•
Do not use oxygen and combustible gases as an energy source for pneumatically operated tools.
εγγράφου δεν αποτελούν συμμόρφωση CE για τα προϊόντα.
•
The operation of this tool can cause sparks and act as a source of ignition for flammable fuels and gases.
IT Vietata la riproduzione senza permesso. Le copie non autorizzate di questo documento non garantiscono la
1. Turn tool sideways with discharge area pointed away from yourself and others. Depress
conformità CE per i relativi prodotti.
the quick release latch inside the tool frame or the latch on the rear of the main frame.
Slide rail to rear. (Fig 1)
NO Skal ikke reproduseres uten tillatelse. Ikke godkjente kopier av dette dokumentet oppfyller ikke kravene for CE-
2. Drop staple stick into magazine. (Fig 2)
merking for produktet.
3. Push rail forward until the latch closes. The tool is now ready for use. (Fig 3)
Note: Use only fasteners recommended by Stanley for use in Stanley Tools or which meet Stanley specifications.
PT Reprodução proibida sem autorização prévia. As cópias não autorizadas deste documento não estão em
conformidade com a CE para os produtos.
TOOL AIR FITTING
This tool uses a free-flow connector plug, 1/4 N.P.T. The inside diameter should be 5mm or larger. The fitting
ES Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
must be capable of discharging tool air pressure when disconnected from the air supply.
OPERATING PRESSURE
SE Prohibida la reproducción sin permiso. Las copias no autorizadas de este documento no suponen la
conformidad con las normas CE de los productos.
70 to 120 p.s.i. (4.9 to 8.4 BAR). Select the operating pressure within this range for best fastener performance.
Caution: Do not exceed the recommended operating pressure.
PL Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
stanowią deklaracji zgodności CE prezentowanych produktów.
AIR CONSUMPTION
CZ Niniejszy dokument nie może być kopiowany bez pozwolenia. Nieautoryzowane kopie niniejszego dokumentu nie
The 216 requires 1.65 cubic feet per minute (.046 cubic meters) and the 216-LN models require 1.8 cubic feet per
stanowią deklaracji zgodności CE prezentowanych produktów.
minute (.051 cubic meters) of free air to operate at the rate of 100 staples per minute, at 80 p.s.i. (5.6 kg/cm
Take the actual rate at which the tool will be run to determine the amount of air required. For instance, if your
SK Rozmnožovanie bez povolenia je zakázané. Neoprávnené kópie tohto dokumentu nie sú v súlade s CE pre dané
fastener usage averages 50 staples per minute, you need 50% of the tool's c.f.m. which is required to operate the
výrobky.
tool at 100 staples per minute.
Stanley offers two types of Operation for the 216 series tools:
HU A dokumentum engedély nélkül nem sokszorosítható. Az engedély nélkül sokszorosított dokumentum nem jelenti
a termék CE-megfelelőségét.
RO Reproducerea neautorizată este interzisă. Copiile neautorizate ale acestui document nu reprezintă
conformitatea CE pentru produse.
GB
2
).
Publicidad
Tabla de contenido
