Publicidad
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
33-0820
33-0825
ITEM
QTY
1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
2
1/2-13 X 2.00" HEX HEAD BOLT
7
2
1/2" FLAT WASHER
8
2
1/2" LOCK WASHER
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
SOPORTE
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
2
PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 2,00"
7
2
ARANDELAS PLANAS DE 1/2"
8
2
ARANDELAS DE PRESIÓN DE 1/2"
1
1
LA BULL BAR
2,3
2
SUPPORT, COTE PASSAGER (2) ET COTE CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
2
BOULONS A TETE HEXAGONALE 1/2-13 X 2,00 PO
7
2
RONDELLES PLATES 1/2 PO
8
2
RONDELLES A FREIN 1/2 PO
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions completely
before beginning.
STEP 2.
NOTE:
It may be necessary to remove/relocate front license plate and license plate bracket. It is not required, but
strongly recommended. If local/state laws requires a license plate, license plate relocation kit 32-0055 is
available.
STEP 3.
Determine passenger and driver brackets.
STEP 4.
Remove six screws from lower part of bumper that secures the plastic shroud. Move the plastic shroud to gain
access to the tow hook bolts.
STEP 5.
Locate and remove the two front 10mm bolts securing the tow hooks to the frame. Attach brackets and fasteners
as shown and repeat for opposite side.
STEP 6.
Attach Bull Bar to mount brackets using 1/2" fasteners. Level and adjust Bull Bar as desired and tighten all fasteners.
Recommended torque values are 43 Ft. Lbs. for 1/2" fasteners and 35 Ft. Lbs. for 10mm fasteners.
LIGHT INSTALLATION:
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension and
socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread nut and
washers on stud and tighten.
started.
NOTE:
Fits most 5" round or rectangle lights. Some lights may require replacing included mount/isolator with rubber
bumpers provided. Mounting stud of 1/2" or less required. Plug mount holes with caps provided if not installing
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1999 1/2-04 NISSAN PATHFINDER
APLICACIÓN: NISSAN PATHFINDER, MOD. 1999 1/2 Y SUPERIOR
APPLICATION: NISSAN PATHFINDER 1999 1/2 ET PLUS
1
CONTENTS -
CONTENIDO
, PASSENGER (2) AND DRIVER (3)
, ACOMPAÑANTE
(2)
SEE FIGURE 1. NOTE:
- CONTENU
Y CONDUCTOR
(3)
A short socket, not a deep well works best to get the nut
2
TOOLS -
HERRAMIENTA
3/4" SOCKET
14MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 3/4
DADO DE 14MM
MANERAL
LLAVE DE TORQUE
DOUILLE DE 3/4 PO
DOUILLE DE 14MM
CLIQUET
Cl DE COUPLE
É
WO:
75-0435 REVISION B 8/26/08
3
- OUTILS
"
Publicidad
Manuales relacionados para Westin 33-0820
Resumen de contenidos para Westin 33-0820
- Página 1 APLICACIÓN: NISSAN PATHFINDER, MOD. 1999 1/2 Y SUPERIOR APPLICATION: NISSAN PATHFINDER 1999 1/2 ET PLUS AUTOMOTIVE PRODUCTS, INC. BULL BAR ASSEMBLY ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN LA BULL BAR 33-0820 33-0825 ITEM CONTENTS - CONTENIDO - CONTENU TOOLS -...
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 VISTA DE LA INSTALACIÓN DEL LADO DEL ACOMPAÑANTE OPUESTO AL LADO DEL CONDUCTOR FIGURE 2 ILLUSTRE: COTE PASSAGER , EN FACE: COTE CONDUCTEUR Thank You for choosing Westin products Westin Automotive Products, Inc. For additional installation assistance please call 5200 N. Irwindale Ave. Suite 220 Customer service (800) 793-7846 or (507) 375-3559 Irwindale, Ca.