Westin 33-1280 Instrucciones

AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
BARRE PARE-CHOC SAFARI
33-1280
33-1285
ITEM QTY
1 1 BULL BAR ASSEMBLY
2, 3 2 BRACKET, PASSENGER (2) AND DRIVER (3)
4 2 PLASTIC PLUG
5 4 RUBBER BUMPER
6 2 1/2-13 X 2.00" HEX HEAD BOLT
7 2 1/2" FLAT WASHER
8 2 1/2" LOCK WASHER
9 6 M10-1.25 FLANGE NUT
1 1 ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3 2 PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
4 2 TAPONES DE PLÁSTICO
5 4 PARACHOQUES DE HULE
6 2 PERNOS CON CABEZA HEXAGONAL DE
7 2 ARANDELA PLANA SAE DE 1/2"
8 2 ARANDELAS DE PRESIÓN DE
9 6 TUERCAS CON BRIDAS M10-1,25
1 1 BARRE PARE-CHOCS SAFARI
2,3 2 SUPPORT,COTE PASSAGER (2) ET COTE CONDUCTEUR (3)
4 2 BOUCHON DE PLASTIQUE
5 4 PARE-CHOCS EN CAOUTCHOUC
6 2 BOULON A TETE HEXAGONALE
7 2 RONDELLE PLATE SAE 1/2 PO
8 2 RONDELLE A FREIN 1/2 PO
9 6 ÉCROU D'ACCOUPLEMENT M10-1,25
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
STEP 1.
completely before beginning.
NOTE:
It will be necessary to remove the front license plate and bracket. Remove license plate from bracket.
STEP 2.
Using a 3/16" drill bit, drill out the two pop rivets that hold the bracket to the bumper. If local/state laws
requires a license plate, license plate relocation kit 32-0055 is available.
Locate factory bolts that hold the bumper support frame to vehicle frame.
STEP 3.
Position brackets onto factory bolts and secure using M10-1.25 flange nuts. Leave loose.
STEP 4.
sit on top of existing nuts.
Attach bull bar hoop to brackets with 1/2" fasteners. Level and adjust bull bar as desired. Torque 1/2"
STEP 5.
fasteners to 65 Ft.Lbs. and M10-1.25 flange nuts to 35 Ft.Lbs.
LIGHT INSTALLATION:
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube. Thread
nut and washers on stud and tighten.
to get the nut started.
NOTE:
Fits most 6" round or rectangle lights. Some lights may require replacing included mount/isolator with rubber
bumpers provided. Mounting stud of 1/2" or less required. Plug mount holes with caps provided if not
installing lights.
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a
regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2003-UP TOYOTA 4-RUNNER
APLICACIÓN: TOYOTA 4-RUNNER, MOD. 2003
APPLICATION: 2003 ET PLUS TOYOTA 4-RUNNER
1
CONTENTS - CONTENIDO
1/2"
1/2-13 X 2.00
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
SEE FIGURE 1. NOTE:
- CONTENU
(2) Y EL CONDUCTOR
1/2-13 X 2.00"
PO
Y SUPERIOR
2
TOOLS - HERRAMIENTA
3/4'' SOCKET
15MM SOCKET
15MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 3/4´´
(3) DADO DE 15MM
LLAVE DE TUERCAS DE 15MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
DOUILLE 3/4 PO
DOUILLE 15MM
CLEF 15MM
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
NOTE:
A short socket, not a deep well works best
WO: 121702
75-0717 REVISION 3/17/06
3
- OUTILS
Bracket will