Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
AUTOMOTIVE PRODUCTS, INC.
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
33-0900
33-0905
ITEM
QTY
1
1
BULL BAR ASSEMBLY
2,3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC PLUG
5
4
RUBBER BUMPER
6
2
1/2-13 X 2.00" HEX HEAD BOLT
7
2
1/2" FLAT WASHER
8
2
1/2" LOCK WASHER
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
SOPORTE
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
2
PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 2,00"
7
2
ARANDELAS PLANAS DE 1/2"
8
2
ARANDELAS DE PRESIÓN DE 1/2"
1
1
LA BULL BAR
2,3
2
SUPPORT, PASSAGER (2) ET CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
2
BOULONS A TETE HEXAGONALE 1/2-13 X 2,00 PO
7
2
RONDELLES PLATES 1/2 PO
8
2
RONDELLES A FREIN 1/2 PO
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
STEP 1.
completely before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the
stainless steel fasteners.
NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not
STEP 2.
required, but strongly recommended. If local/state laws requires a license plate, license plate relocation
kit 32-0055 is available.
Locate and remove the two bolts on each side of the frame rail that hold the tow hook and tie down
STEP 3.
loops on. These bolts will be reused. The tie down loops will not be reinstalled
Determine passenger and driver mount brackets. Place passenger bracket up to frame. Turn passenger
STEP 4.
tow hook backward and reinstall with factory bolts. Install driver bracket with previously removed
fasteners. SEE FIGURE 2.
Attach Bull Bar to mount brackets using 1/2" stainless steel fasteners. Level and adjust Bull Bar as desired
STEP 5.
and tighten all fasteners. Recommended torque values are 37 Ft. Lbs. for 1/2" stainless steel fasteners
and 75 Ft. Lbs. for mounting bracket bolts.
LIGHT INSTALLATION: Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube.
Thread nut and washers on stud and tighten. SEE FIGURE 1. NOTE: A short socket, not a deep well works
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 1998-04 TOYOTA TACOMA
APLICACIÓN: TOYOTA TACOMA, MOD. 1998-04
APPLICATION: 1998-04 TOYOTA TACOMA
1
CONTENTS - CONTENIDO - CONTENU
, ACOMPAÑANTE
(2)
Y CONDUCTOR
(3)
2
TOOLS - HERRAMIENTA - OUTILS
3/4" SOCKET
17MM SOCKET
RATCHET
TORQUE WRENCH
DADO DE 3/4"
DADO DE 17MM
MANERAL
LLAVE DE TORQUE
DOUILLE 1/2 PO
DOUILLE 17MM
CLIQUET
CLE DE COUPLE
WO:
75-0501 REVISION A 3/17/08
3
Publicidad
Manuales relacionados para Westin 33-0900
Resumen de contenidos para Westin 33-0900
- Página 1 Remove the contents from box and check for damage. Verify all parts are present. Read instructions STEP 1. completely before beginning. NOTE: Westin advises the installer to use a thread lubricant on all of the stainless steel fasteners. NOTE: It may be necessary to remove/relocate front license plate and license plate bracket. It is not STEP 2.
- Página 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Página 3 PROTECTION DE LA FINISSION Les produits Westin ont une finission de haute qualité qui requiert des soins, comme toute autre finission du véhicule exposée aux éléments. Protégez la finission à l’aide d’une cire non- abrasive (par exemple, Pure Carnauba) de façon régulière. L’usage de tout savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque les composantes strient la finission et la laissent vulnérable à...