Make Electrical Connection; Complete Installation - ELICA EFS130 Guía De Instrucciones

MAKE ELECTRICAL CONNECTION

WARNING
8.
Electrical Shock Hazard
Disconnect power before servicing.
Replace all parts and panels before operating.
Failure to do so can result in death or electri-
cal shock.
1.
Disconnect power.
G
D
C
A
B
F
2.
Use UL listed wire connectors and connect white wires (A) together.
3.
Use UL listed wire connectors and connect black wires (B) together.
4.
Connect green (or bare) ground wire from power supply to green ground screw in terminal
box. Be sure the ground wire is secured and the screw is well tight.
5.
Install terminal box cover.
6.
Reconnect power.
WARNING
7.
Electrically ground the blower.
Use copper wire. Connect ground wire to
green ground screw in terminal box.
Failure to do so can result in death, fire, or
electrical shock.
Improper grounding can result in a risk or
electrical shock. Consult a qualified elctrician
if the grounding instructions are not
completely understood, or if doubt exists as
to wheter the appliance is properly grounded.

Complete Installation

1. For the EFS130 series install the 75 W (max.) incandescent light bulb.
For the ENM230 and ENM236 series install the 40W (max) halogen lamps with G-9
base. See Range Hood Care section.
2. Replace grease filter if removed. See the "Range Hood Care" section.
3. Check the operation of the range hood fan and light. See "Range Hood Control"
section. If range hood does not operate, check to see whether a circuit breaker has
tripped or a household fuse has blown. Disconnect power and check wiring
connections.
NOTE: To get the most efficient use from your new range hood, Read the "Range Hood
Control" section.
RANGE HOOD CONTROL
Off
Off On Low
A B
A. On / Off light switch
B. Fan speed switch
A. White wires
B. Black wires
E
C. UL listed wire connector
D. Green (or bare) ground wire
E. Home power supply cable
F. UL listed or CSA approved ⁄ " strain relief
1
2
G. Green ground screw
Fire Hazard
EFS130 Serie Model Control and
features:
High
Operating the light
Push the light switch to the left to turn
the light Off.
Push the light switch to the right to the
turn the light On.
Operating the fan
Push the fan switch to the left for Low
speed.
Push the fan switch to the right for
High speed.
Push the fan switch to the middle for
Off.
ENM230 and ENM236 Series Models Control and features
B C D
A
Operating the light
The On/Off light button controls both lights. Press once for On and again for Off.
Operating the fan
The BLOWER SPEED buttons turn the blower on and control the blower speed and
sound level for quiet operation. The speed can be changed anytime during fan oper-
ation by pressing the desired blower speed button. Press the BLOWER OFF button a
second time to turn the blower off.
RANGE HOOD CARE
CLEANING
IMPORTANT: Clean the hood and grease filters frequently according to the following in-
structions. Replace grease filter before operating the hood. Reinstall grease filter correctly
and replace the screw in the vent system.
Exterior Surfaces:
IMPORTANT: Do not use soap-filled scouring pads, abrasive cleaners, Cooktop Polishing
Creme, steel wool, gritty washcloths or paper towels. To avoid damage to the stainless
steel, do not use cleaners that contain chlorine.
Cleaning Method:
■
Rub in direction of grain to avoid scratching or damaging the surface.
■
For stainless steel models, use a special stainless steel cleaner and polish.
■
Liquid detergent or all-purpose cleaner: Rinse with clean water and dry with soft,
lint-free cloth.
■
Glass cleaner to remove fingerprints.
Metal Grease Filter (EFS Series Models)
For ducted installations:
1. Remove screw from the grease filter retainer.
2. Turn the grease filter retainer to release filter.
3. Wash metal filters as needed in dishwasher or
hot detergent solution.
4. Reinstall the filter by placing the back edge in
the channel at rear of hood.
Push filter into place, turn the filter retainer to
secure filter to range hood.
5. Replace screw in the grease filter retainer
For non-ducted (recirculation) installations:
The charcoal filter is not washable. It should last up to 6 months with normal use.
1. Replace metal grease filter with a charcoal filter.
For information on ordering, see the "Accessories" section.
To replace filter:
1.
Remove screw from the grease filter retainer.
2.
Turn the grease filter retainer to release filter.
3.
Reinstall the filter by placing the back edge in the channel at rear of hood. Push filter into
place, turn the filter retainer to secure filter to range hood.
4.
Replace screw in the grease filter retainer.
Metal Grease Filter (for ENM Series Models)
For ducted installations:
1. Press the grease filter retainer to
release filter.
2. Wash metal filter as needed in
dishwasher or hot detergent
solution.
3. Reinstall the filter by placing the
back edge in the channel at rear of
hood. Push filter into place, push
down the filter retainer to secure
filter to range hood.
5
A. On / Off light button
B. Blower Off and Speed minimum
button
C. Blower speed medium button
D. Blower speed maximum button
A
A. Filter retainer
A
B
C
A. Halogen lights
B. Grease filter retainer
C. Grease filter