Traffic Light" Led Indicator (9); Maintenance And Service; Accessories; Storage - Narex ASV 120-2 BASIC Instrucciones De Uso Originales

English
Attention!
The flashlight uses a highly luminous LED as its light source� Make
sure you or other persons (or animals) in your vicinity do not look
directly into the light source� There is a risk of glare, which may re-
sult in subsequent injury of the blinded person (or animal)�
The spotlight (13) can be tilted at a 0° to 90° angle in 30° steps�

"TRAFFIC LIGHT" LED indicator (9)

Battery charge status (capacity) indication:
Activates automatically once you press the switch button (3) and
switches off after approx� 3 seconds� The following LEDs light up
depending on the state of charge (capacity) of the accumulator:
• Accumulator is fully charged: all three status LEDs light up –
green, yellow and red�
• Accumulator capacity has dropped below ca� 60%: only two
status LEDs light up – yellow and red�
• Accumulator capacity has dropped below ca� 30%: only one
status LED lights up – red�
Indication of Reversible Defects
• Indication of low accumulator voltage – can occur when the
accumulator voltage reaches dangerously low levels that
could prevent repeated, proper and safe recharging� The con-
trol system will automatically disconnect the motor and a red
status LED will start flashing; release the switch and press it
again� If the problem persists, take the accumulator out of the
machine and place it in the charger to recharge it� Insert the
other (spare) accumulator into the machine and proceed with
your work�
• Overload indication – can occur as a result of excessive cur-
rent consumption, e�g� at an extremely high torque, in case
of a jammed tool etc� The control system will automatically
disconnect the motor and all three status LEDs will start flash-
ing – green, yellow and red� To restart the machine, release the
switch and then press it again�
• Overheat indicator – can occur in case of a long-term, extreme
load� The control system will automatically disconnect the mo-
tor and two status LEDs will start flashing – yellow and red� Let
the machine cool down before using it again� The cool down
time depends on how overheated the machine is�
Indication of Irreversible Defects
May occur as a result of a combination of factors� e�g� during a short
circuit, motor failure, accumulator failure etc� All three status LEDs
will start flashing – green, yellow and red� If the machine cannot be
restarted as per the above, bring it (along with the accumulator) to
your nearest authorised service centre�
Table overview of problems and signals:
Problem
Voltage too low
LED indicator Red flashing
Machine status Disconnected
Releasing and pressing the button (3)
Turning the
machine on
Inserting
again
a charged battery

Maintenance and service

Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent�
22
Reversible damage
Excess load Overheating
Green, yellow and Yellow and red
red flashing flashing
Disconnected Disconnected
Short-term break
to cool down
Instructions for flashlight cleaning
Clean the external plastic parts by a wet rag and mild detergent�
Though these parts are made of the materials resistant to solvents,
NEVER use any solvent�
Instructions for cleaning the charger
Attention! Risk of electric shock. Prior to start handling
the charger, disconnect the line plug from the socket!
Impurities and dust can be removed from external charg-
er surfaces by a rag or a non-metal brush� Use neither water nor
detergents�
Attention! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website www.narex.cz, section "Service centres"�

Accessories

The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�

Storage

Packed appliance may be stored in dry, unheated storage place
with temperature not lower than -5 °C�
Unpacked appliance should be stored only in dry storage place
with temperature not lower than +5 °C with exclusion of all sudden
temperature changes�

Environmental protection

Power tools, accessories and packaging should be sorted for envi-
ronmental-friendly recy�
Only for EU countries:
Do not dispose of power tools into household waste!
According to the European Directive 2002/96/EC on waste electri-
cal and electronic equipment and its incorporation into national
law, power tools that are no longer suitable for must be separately
collected and sent for recovery in an environmental-friendly man-
ner�

Warranty

Our equipment is under warranty for at least 12 months with re-
gard to material or production faults in accordance with national
legislation� In the EU countries, the warranty period for exclusively
private use is 24 months (an invoice or delivery note is required as
proof of purchase)�
Damage resulting from, in particular, normal wear and tear, over-
Irreversible
loading, improper handling, or caused by the user or other dam-
damage
age caused by not following the operating instructions, or any
Green,
fault acknowledged at the time of purchase, is not covered by the
yellow and red
warranty�
flashing
Complaints will only be acknowledged if the equipment has not
Disconnected
been dismantled before being sent back to the suppliers or to an
Authorised
authorised NAREX customer support workshop� Store the operat-
service centre
ing instructions, safety notes, spare parts list and proof of purchase
in a safe place� In addition, the manufacturer's current warranty
conditions apply�
Note
Due to continuous research and development work, we reserve
the right to make changes to the technical content of this docu-
mentation�