Publicidad
SD20PHL / SD26PHL
GB
WARNING -
safe usage instructions
1. The jacking beam is only to be mounted on lifts
approved by the lift manufacturer for mounting
of jacking beams - be aware that not all lifts are
approved. Rated beam capacity must be max.
2/3 of vehicle lift capacity.
2. Mount the jacking beam with adequate support arms
on horizontal, parallel and solid rails and
secure it against crashing before use. See paragraph
"Assembly Instructions for Support Arms".
3. The jacking beam has been constructed for
operation only by trained personnel, having
read and understood this manual.
4. Check before each lift, that the support arms are cor-
rectly placed on rail of lift or pit edge.
5. This is a lifting device only. Do not move or transport
vehicle with jacking beam.
6. Always lower the jacking beam to the nearest safety
stop immediately - or use axle stands for support
- before working on vehicle.
7. Do not overload, for instance due to sudden external
load. Overload can cause damage or failure of jack.
8. Lift only on points as specified by automaker. During
lifting be attentive that the saddles cannot slide.
9. When lifting the complete vehicle by means of 2
jacking beams they shall be placed minimum
0,85 m from each other.
10. Gravity of load must always be placed centrally. When
lifting by means of only one saddle always place it in
the centre of the jacking beam. Also, the 2 extension
arms must only be used simultaneously.
11. The wheels of the vehicle is to point forward and be
chocked.
12. No person must remain in, on or under a vehicle when
lifted or supported only by the jacking beam.
13. The operator must observe, that the jacking beam can
be operated without any danger to himself and others.
14. The jacking beam as well as the safety valve is not to
be altered.
15. Maximum air-pressure: 12 bar. Full capacity at 8,5
bar.
16. Failure to follow these warnings may result in loss of
load, damage to jack, and/or failure resulting in
personal injury or property damage.
Assembly
See paragraph "Assembly Instructions for Support
Arms" on previous pages.
Air supply through gland on the rear side, ¼" pipe
thread.
Use
Lifting: Turn left handle clockwise. Lower to the nea-
rest safety stop by turning opposite.
Lowering: Lift a little to allow release of safety stop.
Turn both handles counter clockwise
(release valve to the left, release for safety stop to the
right). Both handles automatically return to neutral.
Noise emision: The A-weighted sound pressure level
is max. 85 dB(A).
Maintenance
Maintenance and repairs must always be carried
out by qualified personnel. The air-hydraulic pump
needs oil for lubrication of the mechanical parts. It is
recommended to install water separator/filter and oil
lubricator close to the jacking beam.
Daily: Check jacking beam and supports for damage
- and the correct placement of supports.
Monthly: Lubricate all moving parts with oil. Empty the
water separator and fill the oil lubricator.
Oil refill and check: Lift to maximum height without
load and remove filler plug
to the hole.
WARNING: Do not operate with the filler plug removed
(oil tank will be pressurized).
Oil quantity: 0,6 l. - Any good hydraulic oil with
viscosity
ISO VG 15 can be used.
Never use brake fluid!
Safety inspection
In accordance with national regulations - yet, at least
once a year - the following parts must be checked
by an expert: Supports and support arms (security
against crashing), abnormal wear and damages,
weldings and the hydraulic system for leaks.
Possible faults and how to overcome them
1. The jacking beam cannot lift to maximum height:
Refill the oil tank. (See "Maintenance").
2. The jacking beam cannot lift enough: Check that
release handle is on "neutral" and can move
freely.
3. The jacking beam cannot lower to minimum
position:
Check for damages; lubricate mechanical parts.
4. The jacking beam continues to lower after letting
go of the release handle: Ventilate the hydraulic
cylinder by screw
(10)
Warning: The jacking beam is not to be loaded.
Destruction
The oil must be drained off and legally disposed of.
. Correct oil-level is up
(10)
.
Publicidad
