Publicidad
Idiomas disponibles
Idiomas disponibles
1 BEFORE PROCEEDING
Read all the instructions completely before proceeding. We recommend calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and state building codes.
SINGLE DOOR
2
2D
SIDE JAMB
SIDE JAMB
2D
PENCIL
2F
TEMPLATE
2C
2 DOOR PREPARATION FOR EXIT DEVICE
Mark a horizontally leveled line (2A) 40" [1016 mm] above the Floor on the inside of Door (2B). With door(s) closed, place appropriate side of Template (2C) and align it to the edge of door
(2B) Side Jamb (2D) or to the end of door (2E) as shown. Align the Center Line of template with the Line (2A) drawn on Door (2B). Use the Template Hole Markings to place the hole locations.
Using a Pencil or Awl (2F), tap the screw hole locations through the cross marks on Template (2D). (Mark mounting holes for trim on the outside of door.)
3
3F
PENCIL
VERTICAL
3A
CENTER LINE
3E
TEMPLATE
3 DOOR PREPARATION FOR TOP LATCH DEVICE
With door closed, mark a Vertically Leveled Line (3A) 1 7/8" [37 mm] on the inside of Door (3B) from the edge of Side Door Jamb (3C) or from the End of Door (3D). Using the "Top Latch" side
of Template (3E), fold it along the indicated fold line. Place the fold of template on the corner of door and top Door Jamb (3C). Align the center line of template with the Vertical Line (3A) on
the Door (3B). Use the Template Hole Markings to place the hole locations on Door (3B) and top Door Jamb (3C). Using a Pencil or Awl (3F), tap the screw hole locations through the cross
marks on Template (3E).
4
4E
PENCIL
TEMPLATE
4A
4 DOOR PREPARATION FOR BOTTOM LATCH DEVICE
With door closed, use the "Bottom Latch" side of Template (4A) and fold it along the indicated fold line. Place the fold of template on the corner of Door (4B) and Finished Floor (4C). Align the
center line of template with the Vertical Line (4D) on Door (4B). Use the Template Hole Markings to place the hole locations on Door (4B) and Finished Floor (4C). Using a Pencil or Awl (4E),
tap the screw hole locations through the cross marks on Template (4A).
DOOR
2B
EXIT DEVICE
EXIT DEVICE
DOOR
2B
2A
HORIZONTAL
CENTER LINE
TEMPLATE
2C
PENCIL
2F
DOOR JAMB
3C
3B
DOOR
PENCIL
3F
3E
TEMPLATE
3A
CENTER LINE
VERTICAL
4D
CENTER LINE
DOOR
4B
4E
PENCIL
4C
4A
TEMPLATE
FLOOR
PREPARATION
DOUBLE DOOR
EXIT DEVICE
2E
HORIZONTAL
CENTER LINE
TEMPLATE
2C
3C
3D
DOOR JAMB
VERTICAL
VERTICAL
4D
CENTER LINE
3 / 20
DOUBLE DOOR WITH RIM DEVICE
2B
DOOR
EXIT RIM
STRIKE
DEVICE
2B
DOOR
2A
2C
PENCIL
2F
TEMPLATE
3B
DOOR
PENCIL
3F
3E
TEMPLATE
VERTICAL
3A
CENTER LINE
DOOR
4B
4C
FLOOR
PENCIL
4E
TEMPLATE
4A
DOOR
2B
EXIT DEVICE
2E
2B
DOOR
2A
HORIZONTAL
CENTER LINE
3C
3D
DOOR JAMB
3B
DOOR
VERTICAL
4D
CENTER LINE
4B
DOOR
4C
FLOOR
Publicidad
