Cleaning And Maintenance; Important - Franke SMART PLUS SGP 62 M /F Manual De Instalación Y Servicio

CLEANING AND MAINTENANCE

The oven can be cleaned in conventional manner
(with detergents, oven spray), but only when it is very
dirty and when the stains are particularly stubborn.
For regular cleaning of your oven (after each use), the
following procedure is recommended:
Rotate the operation mode selection knob to the
X X
position „Natural Conventional Cooking"
Set the temperature selection knob/dial to 70°C.
X X
Pour 0.6 liter of water into a baking tray and insert
X X
it into the lowermost guide.
After about twenty minutes, the food residues
„ „
on the enamel will have softened, allowing you
to wipe them with a damp cloth.

Important

Before servicing the oven, always unplug it or
disconnect the power at the main electrical system
switch. Appliance operation is safe with and without
tray guides.
– The stainless steel and enamelled parts of the
oven will stay as good as new if regularly cleaned
with water or special detergents. Take care to dry
them thoroughly after cleaning.
– Never use scouring pads, steel wool, muriatic acid
or other products which could scratch or mark the
surface. Do not use steam cleaners or direct
jets of water.
– Stains on the base of the oven, due to various
cooking products (sauces, sugar, egg white and
fat) are always produced by spills and splashes.
Splashes occur during cooking and are the
„ „
result of cooking at too high a temperature,
while spills are due to the use of cooking
dishes which are too small, or an incorrect
estimate of increases in volume during
cooking.
These two problems can be solved by using
„ „
cooking pots with high rims or using the drip-
tray supplied with the oven.
– To clean the lower part of the oven, it is advisable
to remove any stains while the oven is still warm;
stains are easy to deal with when fresh.
SGP 62 M _/F / SMP 62 M _/F / SMP 66 M _/F
Cleaning the oven door
X
X
.
Removing the oven door internal glass
(models SMP and SGP only) (Fig. 2)
The glasses of the oven door can be removed to
enable thorough cleaning of the internal glasses,
by proceeding as follows:
X
Note: Make sure you turn them fully (the blocks will
click into this position).
X
X
cleaning, always remember to turn both blocks
before closing the door.
Removing the oven door (Fig. 3)
To facilitate oven cleaning, the oven door can be
removed by operating on the hinges as follows:
X
X
X
X
Refer to the pictures at the end of this manual.
– 13 –
The oven door must be cleaned (internally and
X
externally) when the oven is completely cold,
using hot water. Do not use abrasive cloths.
Clean the glass using special detergents.
Clean the enamelled surfaces with hot water
X
and non-abrasive detergent, just as for the oven
interior itself.
With the door completely open, turn the two black
X
blocks (with the word „CLEAN") at the bottom of
the door 180° so that they fit into the seats in the
oven structure.
Carefully lift the internal glasses: the two blocks
X
will prevent the door from closing (if the blocks
are not turned fully, removing the glasses will
cause immediate closing of the door).
After carrying out the cleaning operations, refit
X
the internal glasses (the correct position is
indicated by the words „TEMPERED GLASS" which
must be perfectly legible) and turn the two glass
retaining blocks back to their original position.
Never try closing the door when only one
or both blocks have partially or completely
freed the internal glass panels. After
The hinges are equipped with two moveable locks
X
(A). Lift the lock (A) to release the hinge.
Then lift the door up and pull it outwards; to do
X
this, hold the door at the sides near the hinges.
To refit the door, first slide the hinges into their
X
grooves.
Before closing the door, remember to turn the two
X
locks (A) used as hinge attachments.
EN