X35 System Operation; Charging The Battery; Battery Level Visualization (During Use); Turning The System On/Off And Changing The Assist Level - Orbea BLUE PAPER VIBE 2021 Manual Del Usuario

18 | ORBEA
06 X35 SYSTE M
OPERATI O N
CH A RGING T HE BAT T ERY
To charge the battery, connect the X35 charger to a power
outlet and check that the LED on the charger turns green.
Connect the X35 charger to the ebike's charging port,
aligning the arrows and securing the connection by turn-
ing the safety ring clockwise. The LED on the charger will
turn red. It will turn green once the battery is fully charged.
While the battery is charging, the Iwoc Trio light will fade in
and out, showing the color code for the current battery lev-
el. Once the battery is fully charged, the Iwoc Trio charging
indicator will turn white. Turn the safety ring counterclock-
wise and detach the charger from the charging port.
>25% >50%
<25%
<50% <75%
BATTERY LEVEL VISUALIZATION
(DURING USE)
While the bike is on, the Iwoc Trio will display the current
battery level with the following color codes:
· Solid white: >75% battery charge
· Solid green: 75%-50% battery charge
· Solid orange: 50%-25% battery charge
· Solid red: <25% battery charge
>50% >25%
>75% >25% >15%
<75% <50%
TECHNICAL MANUAL
<15% battery charge: The system will automatically
switch to Level 1 power assist/Eco Mode to save battery.
You can adjust the level of power assist, if you prefer.
<10% battery charge: The system will turn off the pow-
er assist. The ebike lights will stay on for safety reasons
(if in use), and the system will keep recording its location
to allow the user to stop the activity.
TURNING THE SYSTEM ON/OFF
AND CHANGING THE ASSIST LEVEL
BUTTON C: Turn the system ON (short press) or switches
the system OFF (long press) and shows the current assist
level (short press when the system is ON).
>75%
A
BUTTONS A AND B: By single pressing
button A, the power assist level will
be changed to the next level up until
Level 3 is reached. If pressed again,
C
the Trio will vibrate twice to let the cy-
clist know the maximum power assist
level has been reached.
B
A A
B B
ASSIST OFF ASSIST 1 ASSIST 2
>10%
By single pressing button B, the power assist level will be
changed to the next level down until no electric assist is
reached. If pressed again, the Iwoc Trio will vibrate twice
to let the cyclist know that the no power assist level is
reached.
BLUE PAPER VIBE · 2021

TURNING THE LIGHTS ON/OFF

If there is a Mahle Ebikemotion lights cable installed, along
with compatible lights, these can be switched ON and OFF
by following the next procedure:
BUTTON A: Press and hold button A until the Iwoc Trio
light turns yellow. The ebike lights will turn on. Repeat the
same procedure to turn the ebike lights off.
A
RUNNING LIGHTS: The lights on Vibe, both
front and rear, are programmed as running
lights, so they will turn on automatically when
the bicycle is switched on and will turn off
when the bicycle is switched off.
Once the bicycle has been turned on, the li-
ghts can be switched off using the Iwoc Trio
following the method described above.
However, if the user prefers the lights not to
A
turn on upon turning on the bicycle, this be-
B
using the Mahle Ebikemotion Dealer App.
ASSIST 3
WALK ASSIST
By pressing and holding button B on the Iwoc Trio, the
motor will enter WALK ASSIST to help push the bike along.
1 s
B

SYSTEM ERRORS

The Iwoc Trio will indicate an error in the system by
displaying a pink light.
SOLID PINK: The system has gone into SAFE mode. Take
the ebike to an Orbea dealer to diagnose the problem.
BLINKING PINK: There is an error in the system. Check
the User App, which will display the error code, and refer
to the User App troubleshooting guide in this manual to
apply, take the ebike to an Orbea dealer to diagnose the
problem.
ORBEA | 19
EN
1 s
# ERROR