Orbea BLUE PAPER VIBE 2021 Manual Del Usuario página 16

30 | ORBEA
COD. DESCRIPTION
11 COMMUNICATION FAULT LOST FRAME JOB
12 DRIVER ERROR: VG UNDERVOLTAGE
13 DRIVER ERROR OVER TEMPERATURE
14 DRIVER ERROR OVER CURRENT
15 DRIVER ERROR: VDD UNDERVOLTAGE
16 PHASE I SCG
17 PHASE II SCG
18 PHASE III SCG
19 PHASE I SCS
20 PHASE II SCS
21 PHASE III SCS
22 PHASE I CONNECTION ERROR
23 PHASE II CONNECTION ERROR
24 PHASE III CONNECTION ERROR
25 COMPONENT PROTECTOR
TECHNICAL MANUAL
CORRECTIVE MEASURE
Remote control communication error. Check the remote connector.
If the problem persists, contact your ebike dealer.
Battery pack voltage too low. Charge the battery pack.
The ebike is outside of the permissible temperature range. Turn off
the ebike and allow the drive unit to either cool down or heat up to the
permissible temperature. Restart the system. If the problem persists,
contact your ebike dealer.
Current supplied by the battery pack is too high. Reduce the demand.
If the system locks, restart the ebike system. If the problem persists,
contact your ebike dealer.
Battery pack voltage too low. Charge the battery pack.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
Check the motor wire connection and restart the ebike system.
If the problem persists, contact your ebike dealer.
BLUE PAPER VIBE · 2021
COD. DESCRIPTION
26 NVM ERROR PARAMS TO DEALER
27 NVM I ERROR SAVED ERRORS LOST
28 EMN ERROR IMPOSSIBLE SAVE ERRORS
29 BATTERY VOLTAGE SENSOR FAULT
30 OVER CURRENT PROTECTION
31 PEAK OVER CURRENT PROTECTION
32 COMM FATAL ERROR
33 CURRENT NO SPEED
34 ACC VOLTAGE ERROR
35 SENSORS 4V3 ERROR
36 LIGHTS V ERROR
CONSULT THE USER APP MANUAL
Download the complete User App manual for a full guide on all features and functions of the ebikemotion® User App at:
www.ebikemotion.com
CORRECTIVE MEASURE
Take the ebike to your dealer to set to the default system parameters.
Error in the error database system. Restart the ebike system.
If the problem persists, contact your ebike dealer.
Error database system full. Restart the ebike system. If the problem
persists, contact your ebike dealer.
Battery pack sensor damaged. Restart the ebike system. If the problem
persists, contact your ebike dealer.
Current supplied by the battery pack is too high. Reduce the demand.
If the system locks, restart the ebike system. If the problem persists,
contact your ebike dealer.
Current supplied by the battery pack is too high. Reduce the demand.
If the system locks, restart the ebike system. If the problem persists,
contact your ebike dealer.
Fatal error. Restart the ebike system. If the problem persists, contact your
ebike dealer.
contact your ebike dealer.
Power supply problem in the HMI bus. Contact your ebike dealer.
Power supply problem in sensors. Check the wires on the pedaling sensor
(PAS sensor) and motor sensor. If the problem persists, contact your ebike
dealer.
Power output failure in the lights line. Check the wiring and accessory
connected to the light line. If the error persists, disconnect the accessory
and check again. If the error is corrected, the accessory exceeds
manufacturer.
ORBEA | 31
EN