Service; Number" (Pump Number); Radio Communication" (Enable/Disable Radio Comm.); Language - Grundfos TPE2 D Manual Del Usuario

17.29 "Service"

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
"Time until next service" (Motor bearing service)
This display shows when to replace the motor bearings. The
controller monitors the operating pattern of the motor and
calculates the period between bearing replacements.
Displayable values:
• "in 2 years"
• "in 1 year"
• "in 6 months"
• "in 3 months"
• "in 1 month"
• "in 1 week"
• "Now".
"Bearing replacements"
Indicates the number of bearing replacements that have been
done during the lifetime of the motor.
Bearings replaced (Motor bearing maintenance)
When the bearing monitoring function is active, the controller
gives a warning when the motor bearings are to be replaced.
When you have replaced the motor bearings, confirm this action
by pressing [Bearings replaced].

17.30 "Number" (Pump number)

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
You can allocate a unique number to the pump. This makes it
possible to distinguish between pumps in connection with bus
communication.
Factory setting
See section 35. Factory settings.
17.31 "Radio communication" (Enable/disable radio
comm.)
"Radio communication"
Pump variant
(Enable/disable radio comm.)
TPE3, TPE3 D
TPE2, TPE2 D
You can set the radio communication to either enabled or
disabled. You can use this function in areas where radio
communication is not allowed.
IR communication remains active.
Factory setting
See section 35. Factory settings.
50
"Service"
●
●
"Number"
(Pump number)
●
●
●
●

17.32 Language

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
This menu is only available in the advanced control panel.
In this menu you can select the desired language. A number of
languages are available.

17.33 "Date and time" (Set date and time)

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
You can set date and time as well as how they are to be shown in
the display:
• Select date format:
YYYY-MM-DD
DD-MM-YYYY
MM-DD-YYYY.
• Select time format:
HH:MM 24-hour clock
HH:MM am/pm 12-hour clock.
• Set date
• Set time.

17.34 "Unit configuration" (Units)

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
In this menu you can select between SI and US units. The setting
can be made generally for all parameters or customized for each
individual parameter.
Factory setting
See section 35. Factory settings.

17.35 "Buttons on product" (Enable/disable settings)

Pump variant
TPE3, TPE3 D
TPE2, TPE2 D
In this display, you can disable the possibility of making settings.
Grundfos GO
If you set the buttons to "Not active", the buttons on the standard
control panel are disabled. If you set the buttons to "Not active"
on pumps with an advanced control panel, see below.
Advanced control panel
If you have disabled the settings, you can still use the buttons to
navigate through the menus but you cannot make changes in the
Settings menu.
When you have disabled the possibility to make settings, the
symbol appears in the display.
To unlock the pump and allow settings, press
simultaneously for at least 5 seconds.
Standard control panel
The button always remains active but you can only unlock all
other buttons on the pump with Grundfos GO.

Language

●
●
"Date and time"
(Set date and time)
●
●
"Unit configuration"
●
●
"Buttons on product"
(Enable/disable settings)
●
●
and