Safety Instructions - K2 Pumps WPS05001K Manual Del Propietário

PERFORMANCE
Model No.
WPS05001K/ WPS050021K
WPS07501K/ WPS07502K

SAFETY INSTRUCTIONS

Pump clear water ONLY with this pump. Do not pump flammable or explosive liquids such as oil, gasoline,
1.
kerosene, ethanol, etc. Do not use in the presence of flammable or explosive vapours. Using this pump with or near
flammable liquids can cause an explosion or fire, resulting in property damage, serious personal injury, and/or
death.
ALWAYS disconnect the power to the pump before servicing.
2.
Do not touch the motor housing during operation. The motor is designed to operate at high temperatures. Do not
3.
disassemble the motor housing.
Do not handle the pump or pump motor with wet hands or when standing on a wet or damp surface, or in water.
4.
Wear safety goggles at all times when working with pumps
5.
This is a dual voltage 115/230V pump. For model WPS05001K/WPS07501K, VOLTAGE SELECTOR INSIDE
6.
PRESET TO 230V.To change voltage to 115V, please open the terminal cover and set the switch to the proper
voltage. For model WPS05002K/ WPS07502K, pump will auto select proper voltage. All wiring should be performed
by a qualified electrician.
Protect the electrical cord from sharp objects, hot surfaces, oil, and chemicals. Avoid kinking the cord. Do not use
7.
damaged or worn cords.
Ensure the electrical power supply is adequate for the requirements of the pump.
8.
Failure to comply with the instruction and designed operation of this unit may void the warranty. ATTEMPTING TO
9.
USE A DAMAGED PUMP can result in property damage, serious personal injury, and/or death.
10. The pump should be connected to a grounded circuit equipped with a grounded fault interrupter device (GFCI).
11. Know the pump and its applications, limitations, and potential hazards.
12. Secure the pump to a solid base.
13. Periodically inspect the pump and system components. Disconnect the pump from the power supply before
inspecting.
14. Follow all local electrical and safety codes, along with the National Electrical Code (NEC). In addition, all
Occupational Safety and Health Administration (OSHA) guidelines must be followed.
15. The motor of this pump has a thermal protector that will trip if the motor becomes too hot. The protector will reset
itself once the motor cools down and an acceptable temperature has been reached. The pump may start
unexpectedly if it is plugged in.
16. This pump is made of high-strength, corrosion-resistant materials. It will provide trouble-free service for a long time
when properly installed, maintained, and used. However, inadequate electrical power to the pump, dirt, or debris
may cause the pump to fail. Please carefully read the manual and follow the instructions regarding common pump
problems and remedies.
Keep fingers and foreign objects away from ventilation and other openings. Do NOT insert any objects
17.
into the motor.
CAUTION:
Do not touch an operating motor. Modern motors are designed to operate at high temperatures. To
avoid burns when servicing the pump, allow it to cool for 20 minutes after shut-down before handling.
Do not allow pump or any system component to freeze. To do so will void warranty.
Periodically inspect the pump and system components.
Keep the work area clean, uncluttered and properly lighted; store properly all unused tools and equipment.
Keep visitors at a safe distance from the work areas.
WARNING: This pump is designed for indoor installation only. Failure to install indoors will sidnificantly
increase the risk of injury or death from electrical shock
2
GPM of Water @Total Discharge Pressure
HP
0 ft. 5 ft. 10 ft.
1/2 8.1 7.5 6.3
3/4 12.7 10.6 9.5
of 40 psi
15 ft. 20 ft. 25 ft.
6 5.2 4.1
8.5 7.3 5.2
For Professional Technical Support call 1-844-242-2475
Pressure
Max.
Pressure Voltage
shutoff
ON
76PSI 230/115 30
77PSI 230/115 30
switch
OFF
50
50