Beurer PO 60 Manual De Instrucciones

PO 60 Pulse Oximeter
Questions or comments? Call our US-based customer service toll free at 1-800-536-0366.
¿Preguntas o comentarios? Llame a nuestro servicio al cliente en Estados Unidos gratis al teléfono 1-800-536-0366.
Questions ou commentaires? Appelez gratuitement notre service clientèle situé aux États-Unis au 1-800-536-0366.
READ THIS MANUAL COMPLETELY AND CAREFULLY BEFORE USING THIS PRODUCT
Keep this manual in a safe location for future reference
LEA TODO ESTE MANUAL CON ATENCIÓN ANTES DE USAR ESTE PRODUCTO
Conserve este manual en un lugar seguro para consultarlo en el futuro
LISEZ CE MODE D'EMPLOI COMPLÈTEMENT ET ATTENTIVEMENT AVANT D'UTILISER CE PRODUIT
Conservez ce manuel en lieu sûr pour y faire référence ultérieurement
1. IMPORTANT SAFETY NOTES
Signs and symbols
Whenever used, the following signs identify safety and property damage messages and designate a level of hazard or seriousness.
READ THIS ENTIRE MANUAL, THE SAFETY SECTION AND ALL INSTRUCTIONS AND WARNINGS COMPLETELY AND CAREFULLY
BEFORE USING THIS PRODUCT. FOLLOW ALL SAFETY INSTRUCTIONS AND WARNINGS TO AVOID HAZARDOUS SITUATIONS AND
TO MAKE CORRECT USE OF THIS PRODUCT.
Whenever used, the following terms identify safety and property damage messages and designate a level of hazard seriousness.
- This is the safety alert symbol. It alerts you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
WARNING – Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.
CAUTION – Indicates a potentially hazardous situation, which, if not avoided, may result in minor/moderate injury.
NOTICE – Addresses practices not related to personal injury, such as product and/or property damage.
Note
Note on important information
Observe the instructions for use
%SpO Arterial oxygen saturation of haemoglobin (in percent)
PR bpm Pulse rate (beats per minute)
Storage
140°F 95% Storage and transport conditions
(60°C)
-40°F
(-40°C)
Operating
Operating conditions
104°F 75%
(40°C)
50°F
(10°C)
WARNING – To reduce the risk of serious personal injury:
• Do not use the pulse oximeter:
– if you are allergic to rubber products.
– if the device or the finger you are using is damp.
– on small children or babies.
– during an MRI or CT scan.
– while taking a blood pressure measurement on the same arm.
– on fingers that have nail polish, are dirty, have other coatings on them, or have false nails applied.
– on large fingers that do not fit into the device easily (fingertip width greater than 20 mm or thickness greater than 15 mm).
– on fingers with anatomical changes, edemas, scars or burns.
– on fingers that are too small, as with small children for example (width approx. < 10 mm, thickness approx. < 5 mm).
– on people who are not steady at the site of application (e.g. trembling).
– near flammable or explosive gas mixtures.
• Extended use may cause pain for people with circulatory disorders. Do not use the pulse oximeter for longer than two hours on one finger.
• The pulse oximeter displays an instantaneous measurement but cannot be used for continuous monitoring.
• Measurements are for your information only – they are no substitute for a medical examination.
• Check the pulse oximeter regularly before use to ensure that there is no visible damage to the device and the batteries are still sufficiently charged. In case of doubt, do
not use the device and contact customer services or an authorized retailer.
• Do not use any additional parts that are not recommended by the manufacturer.
• Under no circumstances should you open or repair the device yourself. Failure to comply will result in voiding of the warranty. For repairs, please contact customer
services or an authorized retailer.
• Do not look directly inside the housing during the measurement. The red light and the invisible infra-red light in the pulse oximeter are harmful to your eyes.
• This device is not intended for use by people (including children) with restricted physical, sensory or mental skills or a lack of experience and/or a lack of knowledge,
unless they are supervised by a person who has responsibility for their safety or they receive instructions from this person on how to use the device. Children should be
supervised around the device to ensure they do not play with it.
• Neither of the displays for the pulse wave and pulse bar allows the strength of the pulse or circulation to be evaluated at the measurement site. Rather, they are exclu-
sively used to display the current visual signal variation at the measurement site and do not enable diagnostics for the pulse.
CAUTION – To reduce the risk of personal injury or product/property damage:
• Non-observance of the following instructions can lead to incorrect or failed measurements.
• There must not be any nail polish, artificial nails or other cosmetics on the finger to be measured.
• Ensure that the finger nail on the finger to be measured is short enough that the fingertip covers the sensor element in the housing.
• Keep your hand, finger and body steady during the measurement.
• In cases of carbon monoxide poisoning, the pulse oximeter will display a measurement value that is too high.
• To avoid incorrect results, there should not be any strong light sources (e.g. fluorescent lamps or direct sunlight) in the immediate vicinity of the pulse oximeter.
• Protect the pulse oximeter from dust, shocks, moisture, extreme temperatures and explosive materials.
Battery Handling Safety Precautions
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the batteries. Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc or rechargeable batteries) or old batteries with fresh ones. Always replace batteries as a
simultaneous set.
• If the batteries in the device are depleted or the device will not be used for a long period of time, remove the batteries to prevent damage or injury from possible bat-
tery leakage.
• Do not try to recharge batteries not intended to be recharged; they can overheat and rupture (follow battery manufacturer's directions).
• Do not dispose of batteries in fire, batteries may explode or leak.
• Clean the battery contacts and also those of the device prior to battery installation.
• Remove discharged batteries from the product and dispose/recycle in compliance with all applicable laws.
• Keep batteries away from children and pets. Batteries may be harmful if swallowed. Should a child or pet swallow a battery, seek medical assistance immediately.
Notes on electromagnetic compatibility
• The device is suitable for use in all environments listed in these instructions for use, including domestic environments.
• The use of the device may be limited in the presence of electromagnetic disturbances. This could result in issues such as error messages or the failure of the display/device.
• Avoid using this device directly next to other devices or stacked on top of other devices, as this could lead to faulty operation. If, however, it is necessary to use the device
in the manner stated, this device as well as the other devices must be monitored to ensure they are working properly.
• The use of accessories other than those specified or provided by the manufacturer of this device can lead to an increase in electromagnetic emissions or a decrease in
the device's electromagnetic immunity; this can result in faulty operation.
• Failure to comply with the above can impair the performance of the device
2. Intended use
Only use the Beurer PO 60 pulse oximeter on humans to measure the arterial oxygen saturation (SpO2). The pulse oximeter is suitable for private use (at home).
3. Package Contents
• 1 x PO 60 Pulse oximeter
• 1 x Retaining strap
• 1 x Belt pouch
• 2 x 1.5V AAA batteries
• 1 x Instruction manual
• 1 x Quick start guide
4. Parts and Controls
Button
Finger
Opening
5. Before First Use
5.1 Inserting the batteries
1. Slide battery compartment cover open and insert two AAA size alkaline batteries (included) according to the
polarity markings inside the battery compartment.
5.2 Attaching the retaining strap
If desired, attach the retaining strap by routing the small looped end through the small slot near the charging indicator and then insert the larger end through the loop
and pull tight.
6. Functions
The button on the pulse oximeter has various functions in total
Switch-on function Press the button on the pulse oximeter to switch on the device.
Activate and deactivate Bluetooth
® • Briefly press the button on the pulse oximeter to switch on the device.
• Hold the button on the switched on pulse oximeter for 5 seconds to enter the Bluetooth
ON or OFF will appear on the display.
• Briefly press the button to activate ( ON) or deactivate ( OFF) Bluetooth
• To return to measuring, hold the button for 5 seconds.
• To switch off the pulse oximeter, wait 10 seconds. The pulse oximeter will then switch off automatically.
Manufactured for/Manufacturado por/Fabriqué pour
Beurer North America LP, 1 Oakwood Boulevard, Suite 255
Hollywood, FL 33020
ENGLISH
Direct current
Application part, type BF
SN Serial number
Alarm suppression
Device protected against foreign objects ≥ 12.5 mm and against falling
IP 22
drops of water
.
LCD Display Information:
1. Oxygen Saturation Percentage
2. Pulse Rate
5
Slot for
3. Pulse Rate Graph
retaining
4. Pulse Rate Bar
4
strap
5. Low-battery indicator
2. Reattach battery compartment cover.
® .
Transferring measurements to the
'beurer HealthCoach' app and synchronizing
time and date
Brightness function
7. To Use
1. Press the back ends of the PO 60 together to open and insert index finger (preferred) into the opening and hold it steady.
2. Press the Button to activate. Measurements will appear on the LCD Display after a few seconds.
3. If you remove the PO 60 from your finger, it will shut off after about 10 seconds. You can also shut the device off at any time by pressing the Button.
Copying Stored Measurements using Bluetooth
1. Download and install the 'beurer HealthCoach' app from your smartphone's app store.
2. Ensure Bluetooth
® is activated on your smartphone and open the app.
3. Select and add the PO 60 in the settings menu of the app. On the first data transfer a randomly generated six digit PIN code will be displayed on the pulse oxime-
ter. At the same time, an entry field will appear on your smartphone where you should enter this code.
Note: The 'beurer HealthCoach' app and Bluetooth
The time and date will be synchronized with the smartphone during each data transfer.
There are two options for copying data to your smartphone. Make sure that Bluetooth
smartphone and on the pulse oximeter for both options. The 'beurer HealthCoach' app must be active on your smartphone.
Option 1: Hold the button on the switched off pulse oximeter for 5 seconds. 'SYNC' will flash on the display. The device will now attempt to connect to the app for
30 seconds. Once connected, 'SYNC' will stop flashing. All stored measurements will be automatically transferred to the app. The pulse oximeter will then switch off
automatically.
Option 2: After the measurement is completed, the data will be sent automatically to the app. 'SYNC' will flash on the display. The device will attempt to connect
to the app for 30 seconds. Once connected, 'SYNC' will stop flashing. All stored measurements will be automatically transferred to the app. The pulse oximeter will
then switch off automatically.
If Bluetooth
is deactivated ( OFF), the notification will be displayed ( OFF) after your measurements has been carried out.
®
8. Care and Maintenance
• Clean the device with a slightly moistened cloth.
• Do not use detergents or solvents.
• Never immerse the device in water or other liquids.
• When storing the device, first remove the batteries. Make sure no heavy objects are placed on top of it while is it stored. Store in a dry location away from direct sunlight.
Disposal
Observe the local regulations for material disposal. Dispose of the device in accordance with local regulations. If you have any questions, please contact the local author-
ities responsible for waste disposal.
9. Troubleshooting Guide
Problem
Measurements do not display
Measurements are erratic
No data transfer of stored values
10. Specifications
Type
Measurement method
Measurement range
Accuracy
Dimensions
Weight
Sensor
Operating conditions
Storage conditions
Power supply
Battery life
Classification
Data transfer via Bluetooth
®
System requirements for the 'beurer HealthCoach' app
Bluetooth
from version 4.0, iOS from version 10.0, Android
®
List of compatible devices:
The serial number can be found on the unit itself or in the battery compartment.
11. FCC Compliance Information
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference; and (2) this
device must accept any interference received, including interference that may cause undesirable operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if
not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
12. Warranty
Limited Lifetime Warranty For Original Purchaser
1 2 Your Beurer Pulse Oximeter, Model PO 60, is warranted to be free from defects in materials and workmanship for the life of the product under normal conditions of intended
use and service. This warranty extends only to the original retail purchaser and does not extend to retailers or subsequent owners.
We will, at our option, repair or replace the Beurer Pulse Oximeter, Model PO 60, without additional charge, for any part or parts covered by these written warranties. No
%SpO PRbpm
2
98 refunds will be given. Repair or replacement is our only responsibility and your only remedy under this written warranty. If replacement parts for defective materials are
65
not available, Beurer reserves the right to make product substitutions in lieu of repair or replacement.
For warranty service contact our customer service department at 1-800-536-0366 or at info@beurer.com to provide a description of the problem. If the problem is
deemed to be within the scope of the limited lifetime warranty, you will be asked to mail the product at your costs in its original package with proof of purchase, your
name, address and phone number. If the problem is not deemed to be within the scope of the limited lifetime warranty, we will provide a quotation for repair respectively
3
replacement and return shipping fee.
This warranty does not cover damage caused by misuse or abuse; accident; the attachment of unauthorized accessory; alteration to the product; improper installation;
misapplication; lack of reasonable care with respect to the product; unauthorized repairs or modifications; improper use of electrical/power supply; normal wear; loss of
power; dropped product; malfunction or damage of an operating part as a result of failure to comply with instructions for use or to provide manufacturer's recommended
maintenance; transit damage; theft; neglect; vandalism; or environmental conditions; loss of use during the period the product is at a repair facility or otherwise awaiting
parts or repair; or any other conditions whatsoever that are beyond the control of Beurer. This warranty is void if the product is ever used in a commercial or business
environment. The maximum liability of Beurer under this warranty is limited to the purchase price actually paid by the customer for the product covered by the warranty,
as confirmed by proof of purchase, regardless of the amount of any other direct or indirect damage suffered by the customer.
This warranty is effective only if the product is purchased and operated in the country in which the product is purchased. A product that requires modifications or adapta-
tion to enable it to operate in any other country than the country for which it was designed, manufactured, approved and/or authorized, or repair of products damaged by
these modifications is not covered under this warranty.
THE WARRANTY PROVIDED HEREIN SHALL BE THE SOLE AND EXCLUSIVE WARRANTY. ANY IMPLIED WARRANTIES, OBLIGATIONS, OR LIABILITES, INCLUDING BUT NOT
LIMITED TO THE IMPLIED WARRANTY OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THIS APPLI-
CABLE WRITTEN WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitations may not apply to you.
IN NO EVENT SHALL BEURER BE LIABLE FOR ANY SPECIAL, INCIDENTAL, INDIRECT OR CONSEQUENTIAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY,
EXPRESS, IMPLIED OR ANY OTHER THEORY OF LIABILITY, WHATSOEVER. Some states do not allow the exclusion or limitation of special, incidental, or consequential
damages, so the above limitation may not apply to you.
Beurer does not authorize anyone, including, but not limited to, retailers, the subsequent consumer purchaser of the product from a retailer or remote purchaser, to obligate
Beurer in any way beyond the terms set forth herein.
This warranty does not extend to the purchase of opened, used, repaired, repackaged and/or resealed products, including but not limited to sale of such products on Inter-
net auction sites and/or products by surplus or bulk resellers. Any and all warranties or guarantees shall immediately cease and terminate in connection with any products
or parts thereof which are repaired, replaced, altered, or modified, without the prior explicitly written consent of Beurer.
This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state.
Manufactured for:
Beurer North America LP
1 Oakwood Boulevard, Suite 255
Hollywood, FL 33020 USA
Made in China
® settings menu.
There are two options for transferring data to the 'beurer HealthCoach' app. Bluetooth
your smartphone and on the pulse oximeter for both options. Note: The beurer HealthCoach' app must be activated to
allow data transfer.
Option 1: Hold the button on the switched off pulse oximeter for 5 seconds to transfer data to the app.
Option 2: After the measurement is completed, the data will be sent automatically to the app. If Bluetooth
vated ( OFF), the notification will be displayed after your measurements has been carried out.
To select your desired display brightness, hold the button for slightly longer during operation.
®
® must be active to allow data transfer.
® is activated on your
Possible cause
Batteries are depleted
Batteries not inserted correctly
Insufficient circulation in the measurement finger
Measurement finger is too large or too small
Finger, hand or body is moving
Cardiac arrhythmia
'beurer HealthCoach' app is not activated or Bluetooth
®
switched off in your mobile device's settings
Batteries are low or depleted
The device is still switched on
Bluetooth
® is not switched on on your pulse oximeter
PO 60
Non-invasive measurement of arterial oxygen saturation of hemoglobin and pulse rate in finger
SpO 0 – 100%
pulse 30 – 250 beats per minute
SpO 70 – 100%, ± 2%
pulse rate 30 – 250, ± 2 bpm
L 2.3 in x W 1.2 in x H 1.3 in
(L 58.5 mm x W 31 mm x H 32 mm)
1oz (27g) without batteries
Red light (wavelength 660 nm); infrared (wavelength 905 nm); silicon receiver diode
50° – 104° F (10° – 40° C)
≤ 75% relative humidity
700 – 1060 hPa ambient pressure
-40° – 140° F (-40° – 60° C)
≤ 95% relative humidity
500 – 1060 hPa ambient pressure
2 x 1.5VAAA batteries
Approx. two years for three 60-second measurements per day
IP22, application part, type BF
The pulse oximeter uses Bluetooth
® low energy technology, 2.402-2.480 GHz frequency band, max. 2.87 dBm transmission power,
compatible with Bluetooth
® 4.0 smartphones/tablets
from version 5.0.
TM
must be activated ( ON) on
®
is deacti-
®
Solution
Replace the batteries
Reinsert the batteries. If after reinserting the batteries correctly
there are still no measurement values displayed, contact cus-
tomer service
Observe the Important Safeguards section
Fingertip must be 0.39 – 0.79 in (10 – 20 mm) wide and 0.2 – 0.59
in (5 – 15 mm) thick
Keep your finger, hand and body still during the measurement
Seek medical attention
Activate Bluetooth
is ® on your mobile device and restart the app
Replace batteries
Wait for the device to switch off
Activate Bluetooth
®