Ca-Mi NEW HOSPIVAC 400 Manual De Instrucciones página 13

The NEW HOSPIVAC 400 / NEW HOSPIVAC 350 The NEW HOSPIVAC 400 / NEW HOSPIVAC 350 suction equipment does not need maintenance or lubrication. It is necessary to check functioning and
instrument before every use. Unpack the instrument and instrument before every use. Unpack
previous use. previous use.
Always check the integrity of the footswitch power cord. Connect cable to electrical network and turn switch on. Always check the integrity of the footswitch power cord. Connect cable to electrical network and turn switch on.
Close the aspiration outlet with your finger and Close the aspiration outlet with your finger and with suction regulator in maximum vacuum
bar) maximum. Rotate the knob from right to left and check the aspiration regulating control. The vacuum indicator should go down -40 kPa (-0.40 bar). bar) maximum. Rotate the knob from right to left and check the aspiration regulating control. The vacuum indicator should go down -40 kPa (-0.40 bar).
Verify that loud noises are not present, these can indicate wrong functioning. A protection fuse ( F 1 x 4A 250V Verify that loud noises are not present, these can indicate wrong functioning. A protection fuse (
plug protects the instrument. For use replacing plug protects the instrument. For use
Fault type Fault type
1. 1. The suction unit doesn't The suction unit doesn't
work work
2. 2. No No aspiration aspiration
3. 3. No No aspiration aspiration
4. 4. The Vacuum power on the The Vacuum power on the
patient side is either very low patient side is either very low
or absent or absent
5. 5. The The float float doesn't doesn't close close
6. 6. The The float float doesn't doesn't close close
7. 7. Low Low suction suction
Faults 1 1 - - 2 2 - - 3 3 - - 4 4 - - 5 5 - - 6 6 - - 7 7 Faults
If the overfill security system it's activated, don't proceede with If the overfill security system it's activated, don't proceede with the liquid aspiration.
If the overfill security system doesn't work there are two If the overfill security system doesn't work there are two cases:
1° case – If the overfill security system doesn't work the aspiration will be stopped by the bacteriological filter who avoid the liquid penetration inside the device. 1° case – If the overfill security system doesn't work the aspiration will be stopped by the bacteriological filter who avoid the liquid penetration inside the device.
2° case – If both the security system doesn't work, there is the possibility that liquid comes inside the device, in this case return the device to CA-MI 2° case – If both the security system doesn't work, there is the possibility that liquid comes inside the device, in this case return the device to CA-MI
technical service. technical service.
CA.MI. snc will provide upon request electric diagrams, components list, descriptions, setting instructions and any other information that can CA.MI. snc will provide upon request electric diagrams, components list, descriptions, setting instructions and any other information that can
help the technical assistance staff for product repair. help the technical assistance staff for product repair.
BEFORE EVERY CHECKING OPERATION, IN CASE BEFORE EVERY CHECKING OPERATION, IN CASE OF ANOMALIES OR BAD
CA-MI DOES NOT CA-MI DOES NOT GIVE GUARANTEE IF INSTRUMENT, AFTER THE TECHNICAL SERVICE CHECKING, APPEARS TO
Connect the short silicon tube fitted Connect the short silicon tube fitted with the antibacterial filter with the device suction
• •
The other tube, by one end connected with the filter, should instead be connected with the union on the tank lid marked as "VACUUM" in which the The other tube, by one end connected with the filter, should instead be connected with the union on the tank lid marked as "VACUUM" in which the
• •
float (signalling when the device is too full) is fitted. float (signalling when the device is too full) is fitted.
The float signals when the maximum level of volume is reached (i.e. 90% of The float signals when the maximum level of volume is reached (i.e. 90% of the tank volume has already been used) to prevent liquid from entering the
machine (the float closes the machine (the float closes the lid junction).
WARNING: Ensure that the IN marker on the filter is WARNING:
A wrong connection causes immediate destruction in case of contact with sucked A wrong connection causes immediate destruction in case
suction equipment does not need maintenance or lubrication. It is necessary to check functioning and
the instrument and always check always check integrity of plastic parts and feeding cable, they might have been damaged during
with suction regulator in maximum vacuum position check that the vacuum indicators reaches -90
replacing, always check , always check the type and
Cause Cause
Cable is damaged Cable is damaged
External power source failure External power source failure
Jar Jar Cap Cap badly badly screwed screwed down
Lid Lid seal seal not not in in its its seat seat
a) a) Vacuum regulator set to minimum Vacuum regulator set to minimum
b) b) Protection filter blocked or Protection filter blocked or damaged
c) c) Connection tubes blocked, kinked or Connection tubes blocked, kinked or
disconnected disconnected
d) d) Shut-off valve blocked or damaged Shut-off valve blocked or damaged
e) e) Pump motor damaged Pump motor damaged
If If the the cap cap has has been been washed, washed, ensure
float is not partially detached float is not partially detached
The The float float it's it's covered covered by by dirty
Foam inside Foam inside the the jar jar
None of of the None the remedies remedies has
desired results desired results
cases:
GIVE GUARANTEE IF INSTRUMENT, AFTER THE TECHNICAL SERVICE CHECKING, APPEARS TO BE TAMPERED.
with the antibacterial filter with the device suction union (you may choose either
lid junction). This equipment should only be utilised on an horizontal working surface. This equipment should only be utilised on an horizontal working surface.
Ensure that the IN marker on the filter is on the side facing the collection jar lid and fitted into the "VACUUM".
MAINTENANCE MAINTENANCE
integrity of plastic parts and feeding cable, they might have been damaged during
position check that the vacuum indicators reaches -90 kPa (-0.90
the type and the range indicated. the range indicated.
Replace the cable Replace the cable
Check the external power source Check the external power source
down Unscrewed Unscrewed the the cap,
Unscrew Unscrew the the cap
a) a) Turn the vacuum regulator clockwise and check the value of the Turn the vacuum regulator clockwise and check the value of the
damaged vacuum on the gauge vacuum on the gauge
b) b) Replace the filter Replace the filter
c) c) Replace or reconnect the tubes, check Replace or reconnect the tubes, check the jar connections
d) d) Empty the jar, or disconnect the tube from the jar and unblock the Empty the jar, or disconnect the tube from the jar
shut-off valve. The unit twill only work in the shut-off valve. The unit twill only
e) e) Refer to authorised service personnel Refer to authorised service personnel
ensure that that the the Insert the float into it's place Insert the float into it's place
dirty material material Unscrewed the the cap, Unscrewed
Fill Fill the the jar jar to to 1/3 1/3 full full of of ordinary
has achieved achieved the the Contact the seller or CA-MI After-sales Assistance Service Contact the seller or CA-MI After-sales Assistance Service
the liquid aspiration.
OF ANOMALIES OR BAD FUNCTIONING, PLEASE CONTACT CA-MI TECHNICAL
SERVICE. SERVICE.
INSTRUCTIONS INSTRUCTIONS
union (you may choose either the right or the
the tank volume has already been used) to prevent liquid from entering the
on the side facing the collection jar lid and fitted into the "VACUUM".
of contact with sucked liquids. liquids.
13 13
F 1 x 4A 250V ) reachable from exterior and it ) reachable from exterior and it situated in the
Solution Solution
cap, then then rescrew rescrew it it correctly correctly
cap and and insert insert the the seal seal properly properly in in its its seat
the jar connections
work in the upright position
cap, leave leave the the and and put put in in on on autoclave autoclave
ordinary water water
FUNCTIONING, PLEASE CONTACT CA-MI TECHNICAL
the right or the left union).
kPa (-0.90
situated in the
seat
and unblock the
upright position
BE TAMPERED.
left union).