Commissioning The Appliance - Nordcap MORETTI LINK Manual Del Usuario

NOTE:
The stripping of the power cable must be such as
to prevent single-insulated conductors from coming into
contact with the surrounding metal parts. The grounding
conductor must be 50mm longer than the power supply
conductors.
The appliance is delivered with the required voltage indicated on
the plate (Fig. 2).
The connection cable must be supplied by the installer.
For the installation of the power cable:
1. Open the terminal box using a screwdriver as a lever on the side
tabs of the cover: pull and open the cover (Fig. 7).
2. Install the power supply cable: unscrew the screw of the cable
clamp and the three screws of the L-N contacts and then fix the
cables under the heads of the screws by following the colours Blue
(N) Brown (L) Yellow-Green (Fig. 7).
3. Secure the cable in the appropriate cable clamp.
4. Close the terminal box cover.
To connect to the power supply, a plug standardized to the
Standards in force must be installed at the end of the cable.
In addition, these appliances must be included in the circuit of the
equipotential system, the terminal box provided for this purpose
is located on the back of the appliance with the TERMINAL BOX
FOR EQUIPOTENTIAL CONNECTION symbol.
When connection has been completed, check that the supply
voltage, with the appliance running, does not differ from the rated
value by more than ± 5%.
CAUTION!
The flexible wire for connection to the
power supply must have characteristics at least equal to the
model with rubber insulation H05RN-F and must have a rated
section suited to the maximum absorption (see technical data,
TAB. 1).
3 OPERATION
3.1 PRELIMINARY CONTROL OPERATIONS
CAUTION!
Before
programming of the appliance, always check that:
- all electrical and grounding connections have been properly
made.
- all vapour exhaust connection operations have been
properly made.
All control operations must be carried out by specialised
technicians holding a proper license.
CAUTION!
- The appliance must always be under surveillance when in
operation.
- During operation the surfaces of the appliance, and in
particular the glass, become hot, so that care must be taken
not to touch them so as to prevent scalding.
- When opening the doors, keep a safe distance from any
burning steams that could escape from the appliance.
- Do not allow unauthorized people to come close to the
appliance.
For greater uniformity, it is recommended to avoid temperatures
higher than those envisaged for the type of product used.

3.2. COMMISSIONING THE APPLIANCE

The control panel is located on the front right upright of the
appliance (Fig. 8)
1. "DECK 1" temperature adjustment (lower module)
2. "DECK 2" temperature adjustment (upper module)
3. "DECK 1" Timer display (Sec - time expressed in seconds)
4. "DECK 2" timer display (Sec - time expressed in seconds)
5. "DECK 1" set temperature display
6. "DECK 2" set temperature display
7. "TIMER DECK 2" button
commencing start-up and
8. "TIMER DECK 1" button
9. (ON / OFF) main switch
NOTE
: The electronic instrumentation allows a more
precise and punctual adjustment of the appliance. However,
by its nature, it is a more delicate instrumentation than the
traditional one.
For its better preservation, it is recommended to operate the
buttons on the electronic panel board with a light pressure of
the fingers avoiding strokes or excessive pressure.
a) Turn on the main switch (Fig. 8, detail 9) on the right side
of the appliance: both the switch and the electronic panel
board light up.
b) At start up, the lower module "DECK 1" is automatically
activated while the upper module "DECK 2" is turned off
(the display indicates "OFF").
c) Set the desired temperature of the lower module "DECK 1"
by pressing the buttons (Fig. 8, detail 1.) This value appears
on the luminous display (Fig. 8, detail 5). The use of the
resistances is highlighted by the dot in the lower right
corner of the "DECK 1" display
d) Set the desired time of the lower module "DECK 1" by
pressing the "TIMER DECK 1" button for a long time (Fig.
8, detail 8). The set time starts to flash. Adjust the desired
value with the buttons (Fig. 8, detail 1). Wait for the
flashing to end.
e) When the dot in the lower right corner of the "DECK 1"
display goes off it means that the module is at temperature.
Wait a few moments for the temperature to stabilize then
start baking.
f) Activate the timer by pressing the "TIMER DECK 1"
button to start the countdown. At the end, the displays flash.
Press the button again to reset the set time or wait for the
flashing to end and the time will automatically reset.
g) To activate the upper module, press one of the temperature
adjustment buttons (Fig. 8, detail 2). The module activates
with the set temperature shown on the displays (Fig. 8,
detail 6).
h) Set the desired temperature of the upper module "DECK 2"
by pressing the buttons (Fig. 8, detail 2). This value appears
on the luminous display (Fig. 8, detail 6). The use of the
resistances is highlighted by the dot in the lower right
corner of the "DECK 2" display
i) Set the desired time of the upper module "DECK 2" by
pressing the "TIMER DECK 2" button for a long time (Fig.
8, detail 7). The set time starts to flash. Adjust the desired
value with the buttons (Fig. 8, detail 2). Wait for the
flashing to end.
j) When the dot in the lower right corner of the "DECK 2"
display goes off it means that the module is at temperature.
Wait a few moments for the temperature to stabilize then
start baking.
k) Activate the timer by pressing the "TIMER DECK 2"
button to start the countdown. At the end, the displays flash.
Press the button again to reset the set time or wait for the
flashing to end and the time will automatically reset.
l) The maximum temperature that can be set is 280 °C. The
maximum settable time for timers is 300 seconds
m) Simultaneously press the buttons (Fig. 8, detail 2) and keep
them pressed to switch off the upper DECK 2 module when
not in use
n) Simultaneously press the buttons (Fig. 8, detail 1) and keep
them pressed to display the temperatures detected in the
DECK 1 and DECK 2 modules
o) Simultaneously press the "TIMER DECK 1" and "TIMER
DECK 2" buttons (Fig. 8, details 7-8) and keep them
pressed to activate the automatic cleaning cycle, during
which the displays show the wording "CLn" (Cleaning).
p) To turn off the appliance, simply turn off the main switch
(Fig. 8, detail 9).
When switched on again, the control panel will appear as
in point b) with the last settings used.
NOTE:
To prolong the duration over time, it is advisable
to keep the appliance at a high temperature for short periods.
UK/3